Dynabrade Dynorbital-Spirit 59109 Безпека, експлуатація та обслуговування - Сторінка 6
Переглянути онлайн або завантажити pdf Безпека, експлуатація та обслуговування для Шліфувальна машина Dynabrade Dynorbital-Spirit 59109. Dynabrade Dynorbital-Spirit 59109 13 сторінок. 12,000 rpm air powered random orbital sander
3/8" orbit 3/16" orbit 3/32" orbit
Також для Dynabrade Dynorbital-Spirit 59109: Безпека, експлуатація та обслуговування (8 сторінок)
Друкувати сторінку
Vacuum Conversion Instructions (continued)
2. Place 95526 O-Ring on the muffler body between the shoulder and the four (4) protrusions. Using a 12 mm hex wrench (supplied in 57098 Repair Kit),
attach the muffler body and o-ring to the housing through the vacuum adapter.
3. Place vacuum nozzle into the vacuum adapter with the slots facing outward making sure that the knob on the nozzle is aligned with the slot in the adapter.
4. Place 57067 Vacuum Tube into the vacuum adapter with the grooves facing inward until the adapter "snaps" onto the tube and the tube cannot be pulled
out. If the tube can be pulled out, rotate it 1/4 turn and place it back into the adapter until it "snaps".
5. Rotate tube until holes line up. Insert 96197 Dowel Pin in holes until it is centered. Attach machine to portable dust collection system.
Drop-in Motor Removal/Replacement Instructions - Dynorbital -Spirit
Important: Manufacturer's warranty is void if tool is disassembled before warranty expires.
Drop-in Motor Repair Kit P/N 59459 is available which includes special repair tools for the correct removal and replacement of the air motor.
Disconnect tool from power source before motor exchange.
To Remove:
1. Disconnect the sander from the air supply.
2. Invert the sander, and place the 57092 Repair Collar (supplied in the 59459 Drop-in Motor Repair Kit) around the housing and secure in a vise. Padding
can be used on the vise jaws to protect the housing. Important: Do not over tighten the sander in the vise. If the sander is held too tight the removal
of the lock ring and air motor will be difficult.
3. Remove the sanding pad with the 50679 26 mm Open-end Wrench. (Supplied with the sander.)
4. Insert the 56058 Lock Ring Tool (supplied in the 59459 Drop-in Motor Repair Kit) into the corresponding tabs of the lock ring. Loosen the 59058 Lock
Ring turning it counterclockwise.
5. Remove the 59058 Lock Ring and the 50659 O-Ring from the air motor assembly. (3/32" and 3/16" dia. orbits only.)
6. Discard the air motor assembly.
To Install Replacement:
Important: Clean and inspect the housing, valve mechanism, and exhaust assembly. Replace any valve, muffler, or vacuum components as is necessary.
Follow all torque and lubrication specifications.
1. Place the 50569 O-Ring into the 59058 Lock Ring and slip these over the motor shaft balancer. (3/32" and 3/16" dia. orbits only.) Spread 1 drop of
pneumatic tool oil on the surface between the 50569 O-Ring and the 59055 Bearing Plate.
2. Apply 1 drop of oil to the 01024 O-Ring. (O-Ring is supplied with the drop-in air motor assembly.)
3. With the sander housing secured in a vise (use the 57092 Repair Collar of padding on the jaws of the vise to protect the housing) slide the drop-in air
motor into the housing aligning the line-up post with the notch on the inside of the housing. Note: Make certain that the line-up post enters the notch
in the housing and that the 01024 O-Ring remains seated in the side of the cylinder.
4. Tighten the lock ring with the 56058 Lock Ring Wrench. (Torque to 23 N•m/200 in.-lbs.)
5. Install a Dynabrade weight-mated sanding pad.
Drop-in Motor Replacement Complete.
Important: Before connecting the sander to the air supply. depress the throttle lever and place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into the
sanders air inlet. The sander should now be tested at 90 PSIG. operating pressure at the sanders air inlet. Operate the sander for 30 seconds to determine
if it is operating properly and to allow the lubricating oil to permeate the air motor.
Complete Model Description/Housing Number
Model
Vacuum
Number
Description
59000
3-1/2" Non-Vacuum
59001
3-1/2" Basic Vacuum
59002
3-1/2" Deluxe Vacuum
59003
3-1/2" Self Generated Vacuum
59004
3-1/2" Central Vacuum
59005
5" Non-Vacuum
59006
5" Basic Vacuum
59007
5" Deluxe Vacuum
59008
5" Self Generated Vacuum
59009
5" Central Vacuum
59010
6" Non-Vacuum
59011
6" Basic Vacuum
59012
6" Deluxe Vacuum
59013
6" Self Generated Vacuum
59014
6" Central Vacuum
59015
3-1/2" Non-Vacuum
59016
3-1/2" Basic Vacuum
59017
3-1/2" Deluxe Vacuum
59018
3-1/2" Self Generated Vacuum
59019
3-1/2" Central Vacuum
Housing
Model
Number
Number
Description
56620
59020
5" Non-Vacuum
56621
59021
5" Basic Vacuum
56621
59022
5" Deluxe Vacuum
56621
59023
5" Self Generated Vacuum
56622
59024
5" Central Vacuum
56623
59025
6" Non-Vacuum
56624
59026
6" Basic Vacuum
56624
59027
6" Deluxe Vacuum
56624
59028
6" Self Generated Vacuum
56625
59029
6" Central Vacuum
56626
59030
3-1/2" Non-Vacuum
56627
59031
3-1/2" Basic Vacuum
56627
59032
3-1/2" Deluxe Vacuum
56627
59033
3-1/2" Self Generated Vacuum
56628
59034
3-1/2" Central Vacuum
56629
59035
5" Non-Vacuum
56630
59036
5" Basic Vacuum
56630
59037
5" Deluxe Vacuum
56630
59038
5" Self Generated Vacuum
56631
59039
5" Central Vacuum
Vacuum
Housing
Number
56632
56633
56633
56633
56634
56635
56636
56636
56636
56637
56638
56639
56639
56639
56640
56641
56642
56642
56642
56643
6
Model
Vacuum
Number
Description
59040
6" Non-Vacuum
59041
6" Basic Vacuum
59042
6" Deluxe Vacuum
59043
6" Self Generated Vacuum
59044
6" Central Vacuum
59100
3" Non-Vacuum
59101
3" Basic Vacuum
59102
3" Deluxe Vacuum
59103
3" Self Generated Vacuum
59104
3" Central Vacuum
59105
3" Non-Vacuum
59106
3" Basic Vacuum
59107
3" Deluxe Vacuum
59108
3" Self Generated Vacuum
59109
3" Central Vacuum
59110
3" Non-Vacuum
59111
3" Basic Vacuum
59112
3" Deluxe Vacuum
59113
3" Self Generated Vacuum
59114
3" Central Vacuum
™
Housing
Number
56644
56645
56645
56645
56646
56647
56648
56648
56648
56649
56650
56664
56664
56664
56665
56666
56667
56667
56667
56668