Dynabrade Dynorbital-Spirit 59113 Безпека, експлуатація та обслуговування - Сторінка 3
Переглянути онлайн або завантажити pdf Безпека, експлуатація та обслуговування для Шліфувальна машина Dynabrade Dynorbital-Spirit 59113. Dynabrade Dynorbital-Spirit 59113 8 сторінок. 12,000 rpm random orbital sander
Також для Dynabrade Dynorbital-Spirit 59113: Безпека, експлуатація та обслуговування (13 сторінок), Безпека, експлуатація та обслуговування (4 сторінок)
Друкувати сторінку
Important: To keep tool safe a Preventative Maintenance Program is recommended whenever portable power tools are used.
• Use only genuine Dynabrade replacement parts to ensure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
• It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due
to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Filter-Regulator-Lubricator (FRL) – Provides accurate
air pressure regulation and two stage filtration of water contaminates.
• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
Routine Preventative Maintenance: Check free speed of Dynorbital-Spirit
attached with 90 PSIG at inlet while tool is running. Always check tool speed after any maintenance or repair. If tool is operating at a higher RPM (speed)
than marked on the housing, or operating improperly, the tool must be corrected before use.
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• A Drop-In Motor and Tune-Up Kit are available, see specific kit number on page 7.
• Air tool stampings must be kept legible at all times, if not, reorder and replace. User is responsible for maintaining specification information i.e.:
Model #, S/N, and RPM.
• Blow air supply hose out prior to initial use.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
• Protect tool inlet from debris (See Notice Below).
• DO NOT carry tool by air hose.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
• Store accessories in protective racks or compartments to prevent damage.
All Dynabrade motors use the highest quality parts and materials available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
Reference Contact Information
1. American National Standards Institute – ANSI
25 West 43
rd
Street
Forth Floor
New York, NY 10036
Tel: 1 (212) 642-4900
Fax: 1 (212) 398-0023
Maintenance Instructions
®
Notice
All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping
to our customers. If a Dynabrade tool develops a performance problem and an inherent defect is found during normal use and
service, Dynabrade will warrant this tool against defects in workmanship and materials for the lifetime of the tool. Upon
examination and review at our factory, Dynabrade shall confirm that the tool qualifies for warranty status, and will repair or
replace the tool at no charge to the customer. Normally wearable parts and products are NOT covered under this warranty.
Uncovered items include bearings, contact wheels, rotor blades, regulators, valve stems, levers, shrouds, guards, O-rings,
seals, gaskets and other wearable parts. Dynabrade's warranty policy is contingent upon proper use of our tools in accordance
with factory recommendations, instructions and safety practices. It shall not apply to equipment that has been subjected to
misuse, negligence, accident or tampering in any way so as to affect its normal performance. To activate lifetime warranty,
customer must register each tool at www.dynabrade.com. Dynabrade will not honor lifetime warranty on unregistered tools. A
one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to portable
pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty
is non-transferable.
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
regularly using a strobe or magnetic tachometer without abrasive accessory
®
).
Lifetime Warranty
3
3. European Committee for Standardization
Rue de Stassart 36
B - 1050 Brussels, Belgium