Dynabrade Mini-Dynorbital Silver Supreme 69502 Посібник з техніки безпеки, експлуатації та обслуговування - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з техніки безпеки, експлуатації та обслуговування для Шліфувальна машина Dynabrade Mini-Dynorbital Silver Supreme 69502. Dynabrade Mini-Dynorbital Silver Supreme 69502 8 сторінок. 5000 rpm thread-type (1/4"-20), 7500 rpm locking-type, 5000 rpm locking-type, 7500 rpm thread-type (1/4"-20)

Друкувати сторінку

Important: To keep tool safe a preventative maintenance program is recommended whenever portable power tools are used.

• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.

• It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due

to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Filter-Regulator-Lubricator (FRL) – Provides accurate

air pressure regulation and two stage filtration of water contaminates.

• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the

filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.

Routine Preventative Maintenance:

• Regularly check the free speed (RPM) of the Mini-Dynorbital

fastened without any type of sanding accessory attached to the back-up pad. The air pressure must be set to 90 PSIG with tool running. Checking the

RPM requires either a strobe or a magnetic tachometer. This procedure is required after all tool repairs and whenever a tool is issued for use. If the tool

is operating at a higher speed than the RPM marked on the tool housing, or operating improperly, the tool must be serviced and corrected before use.

• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,

ketones, chlorinated hydrocarbons or nitro carbons.

• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

• A Tune-Up Kit is available, see specific kit number on page 7.

• Air tool stampings must be kept legible at all times, if not, reorder and replace. User is responsible for maintaining specification information i.e.:

Model #, S/N, and RPM.

• Blow air supply hose out prior to initial use.

• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.

• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.

After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.

Check for excessive tool vibration.

Handling and Storage:

• Protect tool inlet from debris (See Notice Below).

• DO NOT carry tool by air hose.

• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

• Store accessories in protective racks or compartments to prevent damage.

All Dynabrade motors use the highest quality parts and materials available and are machined to exacting tolerances. The failure of quality pneumatic motors

can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor

bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is

contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of

lubrication during the use of this tool.

All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers. If a Dynabrade tool develops

a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this tool against defects in workmanship and materials for

the lifetime of the tool. Upon examination and review at our factory, Dynabrade shall confirm that the tool qualifies for warranty status, and will repair or replace the tool at

no charge to the customer. Normally wearable parts and products are NOT covered under this warranty. Uncovered items include bearings, contact wheels, rotor blades,

regulators, valve stems, levers, shrouds, guards, O-rings, seals, gaskets and other wearable parts. Dynabrade's warranty policy is contingent upon proper use of our tools

in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment that has been subjected to misuse, negligence, accident or

tampering in any way so as to affect its normal performance. To activate lifetime warranty, customer must register each tool at www.dynabrade.com. Dynabrade will not

honor lifetime warranty on unregistered tools. A one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to

portable pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty is non-transferable.

Reference Contact Information

1. American National Standards

Institute – ANSI

25 West 43

Street

Forth Floor

New York, NY 10036

Tel: 1 (212) 642-4900

Fax: 1 (212) 398-0023

Maintenance Instructions

Silver Supreme Sander. The speed (RPM) is checked with the back-up pad securely

Lifetime Warranty

2. Government Printing Office – GPO

Superintendent of Documents

Attn. New Orders

P.O. Box 371954

Pittsburgh, PA 15250-7954

Tel: 1 (202) 512-1803

Notice

3. Power Tool Institute, Inc.

P.O. Box 818

Yachata, Oregon 97498-0818

Tel: 1 (503) 547-3185

Fax: 1 (503) 547-3539

4. European Committee for Standardization

Rue de Stassart 36

B - 1050 Brussels, Belgium