Dynabrade 40250 Посібник з техніки безпеки, експлуатації та обслуговування - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з техніки безпеки, експлуатації та обслуговування для М'ясорубка Dynabrade 40250. Dynabrade 40250 4 сторінки. Right angle grinder
Друкувати сторінкуPersonal Safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch
on invites accidents.
4. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.
6. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
1. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may
lead to loss of control.
2. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
3. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
4. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures
reduce the risk of starting the tool accidentally.
5. Store idle tools in a high, dry place, locked up out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
6. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the
tool serviced before using. Many accidents are caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous
when used on another tool.
9. Use the right tool. Do not force small tools or attachments to do the job of a heavy duty tool.
Service
1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure
to follow Maintenance Instructions may create a risk of electric shock or injury.
1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments.
2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly
apart and cause injury.
3. Hold tool by insulated gripping surfaces when performing an operation where the tool may contact hidden wiring or its own cord. Contact with a "live"
wire will make exposed metal parts of the tool "live" and shock the operator.
4. Be aware of the acceptable processing of the material you are grinding. Certain material can create an explosive environment.
5" (127mm) or 4-1/2" (114mm) Right Angle Grinder – Is a right angle electric hand tool with a 5/8"-11 spindle which includes: an on/off switch, side handle, a 5" guard,
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool with the wrench provided and the spindle lock on the gear case. The rated RPM
of the accessory must be equal to or greater than the rated RPM of the tool.
Note: Insure that the correct guard is in place for the size wheel being used. 5" (89410 Guard) must be used for 5" wheels. 4-1/2" (89359 Guard) must be used
for 4-1/2" wheels. (Both are supplied with model 40250.)
2. To adjust the guard loosen the 89357 Pinch Screw and position the guard between the operator and the wheel. Securely tighten the pinch screw.
3. Check to make sure the switch is in the off position and connect power source to tool.
4. Hold tool by the motor housing and the side handle. Do Not hold tool by head/housing assembly. Keep hands away from all grinding/sanding
edges and moving parts.
5. Pull trigger to start tool. Release to disengage tool. If lock button is used, depress trigger slightly and it will release.
Important: A preventative maintenance program is recommended whenever portable power tools are used.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model #, Serial # and RPM of your tool.
Routine Preventative Maintenance:
• Mineral spirits are recommended when cleaning the angle head. Do not use on electrical components or clean tool or parts with any solvents or oils containing acids,
esters, ketones, chlorinated hydrocarbons or nitro carbons. Compressed air may be used to remove dirt from electrical components.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• Tool label must be kept legible at all times, if not, reorder Tool Specification Label and replace. User is responsible for maintaining specification information i.e.:
Model #, S/N, and RPM. (See Assembly Breakdown)
• Visually inspect plugs and cords for frays, visible damage and signs of deterioration. Damaged or worn components must be replaced by qualified service personnel.
• Brush Changing – Unplug tool. Remove 89400 Brush Caps and worn 89414 Brushes. Install new brushes and replace brush caps. Run in 30 minutes at free speed to
seat brushes. Brush changing – Change brushes every 100 hrs. to ensure proper tool function. After changing brushes, it is recommended to replace the right angle gear
grease with 95542 Grease.
• After maintenance is performed on tool check for excessive tool vibration.
• Check for excessive current leakage at 550 volts with a current leakage checker on all screws and the gear case, if the electrical components have been
disturbed during repair.
Handling and Storage of Tool and Accessories:
• Use of tool rests, hangers and/or balancers is recommended. Bench mounts are NOT to be used.
• DO NOT carry tool by cord.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
• Store accessories in protective racks or compartments to prevent damage.
SPECIFIC SAFETY RULES
(See Definitions of label symbols on pg. 3)
TOOL DESCRIPTION
and is equipped with a 8 ft. cord set. A 4-1/2" guard is also supplied for use with 4-1/2" wheels.
ASSEMBLY and OPERATION INSTRUCTIONS
MAINTENANCE and ACCESSORY CARE INSTRUCTIONS
®
).
2