Gaggenau VG273320HK Інструкція з експлуатації - Сторінка 9

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Варильна поверхня Gaggenau VG273320HK. Gaggenau VG273320HK 16 сторінок.

Друкувати сторінку

Operating the appliance

N otes

O p e r a t i n g t h e a p p l i a n c e

–

Only use the accessories specified. Do not line the

stainless steel recess (e.g. with aluminium foil).

–

Do not cover the ventilation openings on the back

of the control panel.

–

The burner and ignition plug must be clean and dry.

–

Only light the burners if the pan supports and all

burner parts are correctly fitted.

–

To ignite a burner, firmly press the control knob

down as far as possible and hold it there, then turn

it to the required position.

–

Once ignited, press and hold the control knob for

approx. 2 to 4 seconds to enable the heat sensor

that opens the gas flow to heat up first.

–

If the flame does not ignite within 2 to 4 seconds,

turn the control knob anti-clockwise to the lowest

setting and, once ignited, turn it back to the highest

setting. It can often be quicker to ignite the burner

in the lowest setting because different gases have

different ignition characteristics.

–

When one burner is ignited, an ignition spark will

also be generated at all the other burners.

–

Do not touch the ignition plug while the gas

appliance is being lit.

–

It is important to keep the appliance clean. If the

ignition plugs are dirty, this may cause ignition

problems. Clean the ignition plugs regularly with a

small, non-metallic brush. Take care to prevent the

ignition plugs from suffering any heavy knocks.

Switching on

This appliance is equipped with a step valve. The

markings on the control knob show you the output from

power levels from 1 to 9.

Your gas hob comes with ignition plugs for electrical

ignition.

Place a suitable item of cookware on the pan

support.

Push in the control knob for your chosen burner

and turn it anticlockwise to the power level you

require.

The burner ignites automatically.

Turn the control knob to set the power level.

Caution!

Damage to the appliance

Never try to turn the control knob directly from position

0 to position 1, or from position 1 directly to position 0.

Doing this will damage the step valve.

Warning – Risk of deflagration!

If the burner does not ignite after 15 seconds, switch off

the control knob and open the door or window in the

room. Wait at least 1 minute before igniting the burner

again.

Switching on manually

During a power cut you can ignite the burners manually.

Place a suitable pot or pan on the pot grid.

Press the corresponding control knob and turn it

anticlockwise to the required setting. Keep the

control knob pressed.

Use a gas lighter or a match to ignite the burner.

Keep the control knob pressed for a few seconds

after ignition.

Note: The indicator on the illuminated ring remains off.

Thermoelectric flame monitoring

For your safety, the hob is fitted with thermoelectric

flame monitoring. This prevents the flow of gas if the

burner accidentally goes out while it is in use (e.g. due

to draughts).

If the burner accidentally goes out while it is in use, turn

the control knob to the 0 position and wait at least one

minute before you ignite the burner again.

Switching off

Turn the control knob clockwise to position 0.

Warning – Risk of burns!

When the appliance cover is closed, heat will

accumulate. Only close the appliance cover when the

appliance has cooled down. Never switch the appliance

on with the appliance cover closed. Do not rest food on

the appliance cover or use it to keep food warm.

Residual heat indicator

After switching off the appliance, the illuminated ring on

the control knob slowly flashes orange until the

appliance has cooled enough for it to be safe to touch.

Do not touch the appliance while the residual heat

indicator is flashing.

Operating the appliance