Hi-Tech SHAVGS05 Посібник із швидкого старту

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Система безпеки Hi-Tech SHAVGS05. Hi-Tech SHAVGS05 2 сторінки. Visible signaling appliance

Друкувати сторінку

I. INTRODUCTION

The Safety Hi-Tech model, SHAVGS05 is a high quality visible signaling appliance and the Safety Hi-Tech

model, SHAVGS07 is a high quality visible and audible signaling appliance. The high intensity strobe utilizes

a Xenon flash tube that generates a high-intensity flash visible from all angles. This appliance is intended to

provide a visible or audible/visible, depending on the model, notification signal for the purpose of life safety

and property protection. The SHAVGS05 and SHAVGS07 are provided with a slider switch which allows for

candela selection at the installation site; the candela intensities which can be selected are 15Cd, 30Cd, 60Cd,

75Cd, or 110Cd. This appliance is ideal for any occupancy that requires notification appliances per the

applicable building or fire code or wherever dependable alarms are required. The SHAVGS05 and

SHAVGS07 strobe is listed in compliance with ANSI/UL 1971, Signaling Appliances for the Hearing Impaired

II. LOCATION

This appliance is intended for use in Fire Alarm Systems and is to be installed in accordance with this

manual, the recommendation of the local authorities having jurisdiction, and other NFPA documents that

provide standards on notification appliances for protective signaling systems. The SHAVGS05 and

SHAVGS07 are intended for indoor installations only; this appliance is not listed for outdoor or drip proof

applications.

Wall mounted strobe and horn/strobe appliances shall have their entire lens at heights above the finished

floor of not less than 80 in. (2m) and not greater than 96 in. (2.4m)**. Spacing shall be in accordance with

Table A. If a room configuration is not square, the room size that will entirely encompass the room or

Table A

Room Spacing for Wall-Mounted Visible Appliances

per NFPA 72, 2013 Edition

Minimum Required Light Output

Maximum Room Size

( Effective Intensity, Cd)

One Light

Meters

Feet

per Room

6.10 x 6.10

20 x 20

8.53 x 8.53

28 x 28

9.14 x 9.14

30 x 30

12.2 x 12.2

40 x 40

13.7 x 13.7

45 x 45

15.2 x 15.2

50 x 50

16.5 x 16.5

54 x 54

110

16.8 x 16.8

55 x 55

115

18.3 x 18.3

60 x 60

135

19.2 x 19.2

63 x 63

150

20.7 x 20.7

68 x 68

177

21.3 x 21.3

70 x 70

184

24.4 x 24.4

80 x 80

240

27.4 x 27.4

90 x 90

304

30.5 x 30.5

100 x 100

375

33.5 x 33.5

110 x 110

455

36.6 x 36.6

120 x 120

540

39.6 x 39.6

130 x 130

635

24VDC CLEAR Lens Indoor Strobe Current Ratings

Regulated 24VDC

Strobe

Max. Operating

Candela

Current(mA)

116

110

161

Horn Decibel Levels

Minimum SPL

at 10Ft. (3.05 m)

Horn Mode

Per ANSI/UL 464

(HIGH)

Temp 3 2400Hz

78 dBA

Temp 3 Mechanical

76 dBA

Temp 3 Chime

70* dBA

Continuous 2400Hz

81 dBA

Continuous Mechanical

80 dBA

Continuous Chime

70* dBA

Whoop

82 dBA

Four Lights per Room

(One Light per Wall)

**Effective Intensity Requirements

Visible Notification Appliance

Distance from Ceiling to Top of Lens

greater than or equal to 24 in. (60.96 cm) 110cd

less than 24 in. (60.96 cm)

135

NA = Not allowable

185

Regulated 24VFWR

Max. Operating

NOTICE: DC VOLTAGE RANGE LIMITS:

Current (mA)

16-33V. FWR VOLTAGE RANGE LIMITS:

16-33V. THIS PRODUCT WAS ONLY

TESTED TO THE STATED VOLTAGE

102

RANGE(S); DO NOT APPLY 80% AND 110%

161

OF THIS RANGE FOR SYSTEM

225

OPERATION.

256

Horn Current Ratings Over

Input Voltage Range of 16-33V

Minimum SPL

Regulated 24VDC

at 10Ft. (3.05 m)

Max. Operating

Per ANSI/UL 464

Current (mA)

(LOW)

HIGH Setting

71* dBA

70* dBA

66* dBA

74* dBA

72* dBA

66* dBA

69* dBA

SHAVGS05 - VISIBLE SIGNALING APPLIANCE

ANSI/UL 1971 COMPLIANT

SHAVGS07 - VISIBLE AND AUDIBLE SIGNALING

APPLIANCE

ANSI/UL 1971 and ANSI/UL 464 COMPLIANT

subdivide the room into multiple squares shall be used. Wall mounted horn only appliances shall have their

tops above the finished floors at heights of not less than 90 in. (2.30 m) and below the finished ceilings at

heights of not less than 6 in. (152 mm). Different mounting heights shall be permitted by the AHJ provided

the sound pressure level requirements of NFPA 72 are met.

III. MOUNTING, ROUGH-IN BOX AND RUN WIRING

This unit is designed for mounting to most single gang boxes, 4 in (10.16 cm) square outlet boxes, 2-gang

masonry boxes or non-metallic 2-gang switch boxes. Conduit entrance to boxes should be selected to insure

sufficient wiring clearance.

1. Run a minimum 18 gauge insulated 2 or more conductor cable.

2. Mount a box for each remote signaling appliance. Screw bracket onto box. Insert signal into bracket and

slide to the right firmly into the terminal block receptacle. Place housing over mounted assembly and

screw together with single screw at the bottom of the signal. Cover screw with plastic tab.

NOTICE: WIRING SHOULD BE CONNECTED TO MOUNTING BRACKET PRIOR TO MOUNTING SIGNAL.

INCOMING POSITIVE POWER LEAD MUST BE BROKEN AND EACH LEAD IS TO BE INSERTED INTO

EACH OF THE TOP TWO TERMINALS. IF TWO POWER RUNS ARE MADE TO THE SIGNAL, ONE FOR

THE STROBE AND ONE FOR THE HORN, ONLY ONE OF THE RUNS MUST HAVE ITS POSITIVE LEAD

BROKEN AND PLACED UNDER THE TWO SEPARATE TOP TERMINALS. A BARRIER IS PROVIDED TO

PREVENT BOTH LEADS FROM BEING PLACED UNDER THE SAME TERMINAL.

CAUTION:

Strobe light must be

installed within 16 feet of

the pillow when used in a

sleeping area.

furniture or walls block strobe light.

NOTICE:

w THE VISUAL SIGNAL MUST BE IN THE DIRECT VIEWING AREA OF THE

w VISUAL SIGNALS FOR THE HEARING IMPAIRED ARE ONLY ONE METHOD OF

for Sleeping Areas

Intensity

w THE STROBE LIGHT MUST BE SEEN BY THE SLEEPING PERSON. IF THE

177cd

SHAVGS05 AND SHAVGS07 PRODUCT INFORMATION

NOTICE:

Regulated 24VFWR

w THE THREE PULSE TEMPORAL PATTERN IS TO BE USED FOR EVACUATION USE

Max. Operating

ONLY.

Current (mA)

w THE SOUND OUTPUT FOR THE TEMPORAL 3 TONE IS RATED LOWER SINCE THE

HIGH Setting

TIME THE HORN IS OFF IS AVERAGED INTO THE SOUND OUT PUT RATING.

WHILE THE HORN IS PRODUCING A TONE IN THE TEMPORAL 3 MODE ITS SOUND

PRESSURE IS THE SAME AS THE CONTINUOUS MODE. UNITS HAVE BEEN

TESTED TO 0°C, 49°C AND 93% HUMIDITY.

* Operating the horn in this mode at this voltage will result in not meeting the minimum

ANSI/UL 464 sound level required for public mode fire protection service. These settings

are acceptable only for private mode fire alarm signaling use. Use the high dBA setting

for public mode applications (the chime tone is always private mode).

Strobe light can not be seen when objects such as doors,

OCCUPANT IN ORDER TO BE SEEN.

ALERTING THE HEARING IMPAIRED. VISUAL SIGNALS MAY NOT BE THE

PREFERRED METHOD FOR NOTIFYING ALL HEARING IMPAIRED

INDIVIDUALS.

PERSON HAS HEAD TURNED OR OTHERWISE UNABLE TO BE ALERTED BY

VISUAL, THE STROBE WILL NOT BE EFFECTIVE.

550-0621

Page 1