DYNACO Stereo 70 Інструкція по збірці - Сторінка 13

Переглянути онлайн або завантажити pdf Інструкція по збірці для Підсилювач DYNACO Stereo 70. DYNACO Stereo 70 16 сторінок. Series ii tube amplifier
Також для DYNACO Stereo 70: Посібник з реставрації (20 сторінок), Посібник з реставрації (5 сторінок), Посібник користувача (12 сторінок)

Друкувати сторінку

which are standard dealer items can be purchased

from most electronic supply stores.

transformers are returned for factory repair

or exchange, they should be removed from the

equipment without cutting the leads short.

leads

have been cut rather than unsoldered, so that they

are no longer usable, the guarantee on the trans-

former is voided.

In the event that the assembled kit does not

function properly or breaks down after some use,

Dyna Company will service the kit for a service

fee of $7.50 plus the cost of parts which have been

damaged by the user or are past the guarantee

period. This service facility is not available for

kits which are incompletely wired, or have been

wired with other than rosin core solder, or in

which changes or modifications have been made

without fa c tor y authorization.

In addition, NO

PARTS WILL BE REPLACED NOR WILL ANY

SERVICE BE AVAILABLE FOR KITS WHERE

THE GUARANTEE POST CARD HAS NOT BEEN

RETURNED.

THE SERIAL NUMBER ON THIS

INSTRUCTION BOOK MUST BE MENTIONED IN

CORRESPONDENCE, PARTS RETURN, OR KITS

RETURNED FOR FACTORY SERVICE.

is the

factory prerogative to limit the service facility to

one year from date of purchase.

When shipping the amplifier for service, a note

must be attached specifying the symptoms, the

name and address of the sender, and the serial

number of the unit.

The kit should be securely

packed with stuffing inside the cover to prevent the

tubes from falling out of the sockets.

should be

placed in a rugged carton surrounded by several

inches of shredded paper or other soft packing

material. The original carton is not suitable for

shipp ing a wired amplifier.

Shipment should be made by prepaid Railway

Express, where possible; and repaired kits will be

returned by Railway Express COD for freight and

service charges unless these charges have been

prepaid.

Parcel post is not a safe method for

shipment of completed kits and should not be used.

Dyna Company assumes no responsibility or

liability for dam age s or injuries sustained in

assembly or operation of the Dynakit.

STEREO 70 PARTS LIST

(Parts of similar type which do not change performance may sometimes be included as a matter of expediency).

1 - Chassis set (including cover and bottom plate)

1 - Power Transformer - PA-060

2 - Output Transformers - A-470

1 - Choke - C-354

4 - Output Tubes - EL-34

1 - Rectifier Tube - GZ -34

2 - Driver Tubes - 7199

7 - Octal sockets

1 - Printed Circuit Assembly - PC-3

1 - Filter Capacitor - Quad

525V

2 - Capacitors - 50 MFD

1 - Dual Ceramic Capacitor - 2 x .02 MFD

1 - Selenium Rectifier

2 - Four Screw Terminal Strips

1 - Fuse Post plus rubber washer and mounting nut

1 - Fuse - 3A Sio-Blo

1 - Line Cord

1 - On-Off Switch (SPST)

1 - Input Switch (SPDT)

1 - Dual Input Socket

1 - Input Socket Insulator

2 - Potentiometers 10,000 ohm

1 - Seven Lug Terminal Strip

1 - Hank Wire

RESISTORS

2 - 15.6 ohms

4 - 1000 ohms (brown-black-red)

2 - 10,000 ohms (brown-black-orange)

2 - 470,000 ohms (yellow-violet-yellow)

2 - 10 ohms (brown-black-black)

1 - 6800 ohms (blue-grey-red)

1 - 22,000 ohms (red-red-orange)

4 - Rubber Feet

33 - 4/40 x 1/4" Screws

31 - 4/40 Nuts

30 - #4 Lockwashers

1 - 4/40 x 3/4" Screw

4 - #6 Sheet Metal Screws

10 - 8/32 Screws

14 - 8/32 Nuts

14 - #8 Lockwashers

1 - Rubber Grommet

2 - Solder Lugs

2 - 3/8 Lockwashers

2 - 3/8 Nuts

2 - Cable Clamps

1 - Set Instructions & Pictorials