GREAT PLAINS HP-100 Dual-Flo Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Водяний насос GREAT PLAINS HP-100 Dual-Flo. GREAT PLAINS HP-100 Dual-Flo 4 сторінки. Petroleum hand pump

Друкувати сторінку

HP-100 Dual-Flo

Petroleum Hand Pump

Owner's Manual

GENERAL INFORMATION

The GPI HP-100 DUAL-FLO

signed to manually pump petroleum products compatible

with aluminum and Buna-N. The user has the flexibility of

operating the pump at two flow rates. A setting of 1/2-gallon

provides faster high-capacity flow. A 1/4-gallon setting al-

lows for easier pumping of fluids. The HP-100 Hand Pump is

designed for use on a tank with a 2-inch bung.

Read Me!

Observe standard precautions when handling fuel.

• Keep fuel away from open flame or spark.

• Do not refuel vehicles or equipment with engines running

or while equipment engine is hot.

• Do not smoke while refueling.

Use the HP-100 Hand Pump only with petroleum products

such as diesel fuel, kerosene, and gasoline. This equipment

should not be used to pump chemicals.

Damage Inspection

Upon receipt of your pump system, carefully inspect visible

components for any damage that may have occurred during

shipping. Note that the pump includes a suction pipe, dis-

charge hose, and nozzle. If any parts are damaged or

missing, please contact your distributor.

INSTALLATION

Use the following procedures to install the HP-100 Hand

Pump on a tank with a 2-inch bung.

Install Suction Pipe

1. Remove the two protective plugs from the pump inlet and

outlet ports.

2. Wrap the threaded end of the suction pipe with 3 to 4 turns

of Teflon

tape.

3. Insert the suction screen into the inlet cover.

4. Place the spacer in the inlet cover to secure the inlet screen.

5. Install the suction pipe into the inlet cover and tighten

firmly with a pipe wrench.

11/02

Petroleum Hand Pump is de-

" A G r e a t P l a i n s Ve n t u r e s S u b s i d i a r y "

www.gpi.net

1-800-835-0113

Install Pump on Tank

1. Before installing the pump, clean the tank interior of all dirt

and foreign material.

2. Lubricate the threads of the inlet cover with Teflon

or a thread-sealing compound approved for use with

petroleum fuels.

3. Extend the adjustable suction pipe to its full length and

carefully insert it into tank opening. The suction pipe will

adjust to the length needed and rest on the bottom of tank.

NOTE: The suction pipe supplied has a variable length of 22

to 40 inches. If additional length is needed, order the 15-

inch Suction Pipe Extension Kit.

4. Thread the inlet fitting of the pump onto the tank and turn

the pump to tighten snugly.

NOTE: To prevent the buildup of pressure and possible fuel

leakage through the nozzle, make sure the tank is vented.

Install Hose and Nozzle Assembly

Apply 3 to 4 wraps of Teflon

hose and hand-tighten into the outlet cover until snug.

Install Handle

The HP-100 Hand Pump gives the operator a choice of two

flow settings:

• 1/4 gallon setting has low resistance and pumps 1/4

gallon per stroke cycle.

• 1/2 gallon setting has higher resistance and pumps 1/2

gallon per stroke cycle.

Volume per stroke is determined by connecting the piston

shaft to the appropriate handle setting as outlined below.

NOTE: Clevis pins may be installed from either side of handle.

1. Slide the handle grip onto the pump handle.

2. To install the links on the pump, insert a long clevis pin

through the link ends and the pump's link holes. Secure

with a small cotter pin. (Figure 1)

5252 East 36th Street North

Wichita, KS USA 67220-3205

TEL: 316-686-7361

FAX: 316-686-6746

tape

tape to the threaded end of the

Figure 1

Rev. -

921407-09