GREAT PLANES Silhouette Інструкція з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Іграшка GREAT PLANES Silhouette. GREAT PLANES Silhouette 16 сторінок.
Друкувати сторінку
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and fl yability of your fi nished model depends
on how you build it; therefore, we cannot in any way
guarantee the performance of your completed model,
and no representations are expressed or implied as to
the performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
DECISIONS YOU MUST MAKE
This is a partial list of items required to fi nish the Silhouette
3D ARF that may require planning or decision making before
starting to build. Order numbers are provided in parentheses.
Motor Battery
For best fl ight performance a lightweight battery is
recommended. We recommend the Great Planes Power
Series 11.1 volt 640mAh 20C LiPo battery (GPMR0601).
Radio Equipment
❏
4-channel radio system is required.
❏
(4) Futaba
®
S3114 Micro High Torque servos (FUTM0414)
❏
(1) 6" Y-harness (FUTM4130)
❏
(2) 150mm Slim Wire Servo Extensions (FUTM4506)
❏
(2) 300mm Slim Wire Servo Extensions (FUTM4507)
5
4
6
KIT INSPECTION
1
5
3
2
❏
™
RimFire
400 (RimFire 28-30-950 GPMG4560)
❏
12 amp Brushless ESC is recommended (GPMM1810)
❏
11x3.8 Slo-Flyer Propeller (APCQ5017)
ADHESIVES & BUILDING
SUPPLIES REQUIRED
This is the list of Adhesives and Building Supplies that are
required to fi nish the Silhouette 3D ARF.
❏
UFO Foam-safe Thin CA 1oz. (HOTR1040)
❏
Great Planes Pro
™
Foam-safe Medium CA 1oz.
(GPMR6069)
❏
CA Activator Foam-safe 2oz. pump (GPMR6035)
❏
#55 (3/64") drill bit
❏
Drill
❏
36" (914mm) Ruler (HCAR0475)
❏
Hobby Knife with 5 blades (HCAR0101)
❏
Phillips head screw driver
IMPORTANT BUILDING NOTES
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
• The stabilizer and wing incidences and motor thrust angles
have been factory-built into this model. However, some
technically-minded modelers may wish to check these
measurements anyway. To view this information visit the web
site at www.greatplanes.com and click on "Technical Data."
Due to manufacturing tolerances which will have little or no
effect on the way your model will fl y, please expect slight
deviations between your model and the published values.
Before starting to build, take an inventory of this kit
to make sure it is complete, and inspect the parts
to make sure they are of acceptable quality. If any
parts are missing or are not of acceptable quality,
or if you need assistance with assembly, contact
Product Support.
Great Planes Product Support
3002 N Apollo Drive, Suite 1
Telephone: (217) 398-8970, ext. 5
E-mail: [email protected]
1. Fuselage
2. Wing
3. Horizontal Stab
3
Motor
Champaign, IL 61822
Fax: (217) 398-7721
4. Wheels (2)
5. Wheel Pants (2)
6. Main Landing Gear