Daytona 56687 Посібник користувача та інструкції з техніки безпеки - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник користувача та інструкції з техніки безпеки для Валети. Daytona 56687. Daytona 56687 4 сторінки.
Друкувати сторінку
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
WARNING! TO PREVENT SERIOUS INJURY: Use as matched pair to support one end of a vehicle only.
Supporting a Vehicle
1. Make sure the vehicle does not exceed the capacity
of the Jack Stands. Note: Check that the weight
is evenly distributed between the Jack Stands.
You must evenly distribute the weight or the
Jack Stands may fail, causing severe injury
or death. Only apply the load vertically.
WARNING! TO PREVENT SERIOUS INJURY: If a
vehicle drops on the Jack Stands (even if it is under
the weight capacity limit), the principle of "dynamic
loading" takes affect. The force of the weight
falling may cause the Jack Stands to fail. A vehicle
weighing much less than the Jack capacity may
cause the Jack Stands to fail if dropped on them.
Note: Do not move the Handle when the Jack
Stands are supporting a vehicle. The shear pin is
designed to shear in the event the user attempts to
move the Handle while supporting weight. If the pin
shears, do not use the Jack Stands again until the
shear pin is replaced by a qualified technician.
2. Examine Jack Stands for cracks or damage before
each use. Do not use if even a minor crack,
bend, or other damage/deformation appears.
Discard Jack Stand if damaged or deformed.
Removing the Jack Stands
1. Raise the vehicle with a floor jack to take
the load off of the Jack Stands.
2. Raise the Handle on the Jack
Stands and lower the Posts.
3. Remove the Jack Stands. Use the floor jack
to safely lower the vehicle to the ground.
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.
If abnormal noise or vibration occurs, have the problem corrected before further use.
1. Periodically clean the bottom of the Bases and
top of Posts of any dirt, grease, or debris.
Item 56687
For technical questions, please call 1-888-866-5797.
3. Remove the Pin on each Jack Stand
to completely lower the Post.
4. If your are raising only one end of the vehicle,
block the tires that remain on the ground.
5. Following the instructions in your floor jack
manual, raise your vehicle to just above the
minimum height of your Jack Stands.
6. Slide your Jack Stands to the proper position points
referred to in the vehicle owner's manual. Make sure
the Jack Stands are on the same point on each side
of the vehicle. Move the Handle up, and raise the
Jack Stands until they are just below the jack contact
point on the vehicle. Align the holes in the Sleeve
with the hole in the Post and insert the Pin all the way
through. Center the load on the Saddle of the Post.
Release the Handle so that ratchet catches on the
Pawl. Gently lower the vehicle with the floor jack.
WARNING! TO PREVENT SERIOUS INJURY:
Set both the Jack Stands to the same height.
7. Determine if the vehicle is stable. If not, raise
the vehicle and reposition the Jack Stands.
WARNING! TO PREVENT SERIOUS INJURY:
Do not use Jack Stands as a permanent stand for
the vehicle. Use them only while making repairs,
then immediately lower vehicle to the ground.
2. Before each use, inspect the general condition
of the Jack. Check for broken, cracked, or bent
parts, loose or missing parts, and any condition
that may affect the proper operation of the
product. Do not use damaged equipment.
Discard Jack Stand if damaged or deformed.
Page 3