HID iCLASS SE R40E Посібник з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з монтажу для Зчитувач карток HID iCLASS SE R40E. HID iCLASS SE R40E 14 сторінок.

Друкувати сторінку

INSTALLATION GUIDE

Mounting

Junction box

not included

Gasket optional

Wiring

18 in

(0.46 m)

PIGTAIL***

TERMINAL

Yellow

P1-1

Orange

P1-2

Black

P1-3

Red

P1-4

Drain

P1-5

Brown

P1-6

Blue

P1-7

Red/Green

P2-7

Tan

P2-6

Violet

P2-5

White

P2-4

Green

P2-3

Pink

P2-2

Gray

P2-1

* Tamper Output. When activated, output syncs to ground (default).

** Dependent upon reader configuration. See HTOG Wiegand and Clock-and-Data

configurations for more information.

*** For 5 meter pigtail readers, PN: 9xxxxxLEKxxxxx follow the wiring diagram on the reader.

Optional Features

Open Collector Output - Controls an external device (5 VDC) operating in Host Mode only. Sink – 40mA / Source – 1mA.

Optical Tamper – A configuration card is necessary to activate the Optical Tamper. Once activated, and when the mounting plate is removed, the Optical

Tamper is activated. Contact HID Technical Support for Optical Tamper options.

Configuration Cards – With the use of configuration cards, the reader can be modified to meet the specific requirements of an installation. Configuration

options include; audio visual, CSN outputs and keypad outputs (keypad models only). Contact HID Technical Support for all reader configuration options.

Hold Input – when asserted, this line either buffers a card or disables a card read until released, as configured.

hi dg l o b a l.com

R10E, RP10E, R15E, RP15E, R40E, RP40E, RK40E, RPK40E, R10MA, RP10MA, RP15MA, R40MA, RP40MA, RPK40MA

ATTENTION

Observe precautions for handling

ELECTROSTATIC SENSITIVE DEVICES

BEEP

GPI01

GRN

GPI02

GND

OC/TMPR

+VDC

DATA1/CLK

DRAIN

DATA0/DATA

RED

GPI03

HOLD

GPI04

DESCRIPTION

Beeper Input

LED Input (GRN)

Ground (RTN)

+VDC

Unused

LED Input (RED)

Hold Input

GPI01/OSDP (RS485-FDX/HDX-A)

GPI02/OSDP (RS485-FDX-HDX-B)

*Open Collector Output/Tamper

**Wiegand Data 1 / Clock

**Wiegand Data 0 / Data

GPI03 (RS485-FDX-Z)

GPI04 (RS485-FDX-Y)

An ASSA ABLOY Group brand

iCLASS SE/multiCLASS SE

Install Reader to Backplate

Power & Testing

Turn on power

Note: Previous iCLASS readers had reversed RS-485 wiring (P2-7 & P2-6 - A

& B). When upgrading to an iCLASS SE reader, ensure proper connections

as defined below.

Note: It's possible to reuse existing Wiegand wiring for OSDP, however,

using simple stranded cable typical of Wiegand access control readers is

usually not meeting the RS485 twisted pair recommendations.

Note: For OSDP cable lengths greater than 200ft. (61M) or EMF

interference, install 120Ω +/- 2Ω resistor across RS-485 termination ends.

Note: Wiring the reader incorrectly may permanently damage the reader.

Note: With a keypad reader, operating as 26 bit emulation; upon power up

you have 5 seconds to enter the facility code followed by #. If unsuccessful,

the reader LED displays solid Red. Power-cycle the reader and retry

entering the facility code.

The facility code needs to be manually entered as 3 digits (i.e. if facility

code is 10 enter 0-1-0-#). Note: SE readers only use facility codes between

1-255, and there is no default facility code. Once the facility code has been

entered, the LED will display Violet and then to a final Red. Then power-

cycle the reader. Note: When using a keypad, if there are 2 short beeps

after entering your PIN, the reader does not have a facility code configured

yet. In this event, an Admin will need to be power-cycle the reader and

enter the facility code before the reader will accept your PIN.

Page 2

PLT-01579 A.4

Test card