AFG 2.0AS Assembly and Посібник з монтажу та експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Домашній тренажерний зал AFG 2.0AS Assembly and. AFG 2.0AS Assembly and 16 сторінок. Afg series
Також для AFG 2.0AS Assembly and: Посібник з монтажу та експлуатації (15 сторінок)
Друкувати сторінку
iI_ ii_i
i
_
i i
i I
H
il_ _ iii_i
_i _i! I_ i i_ i i_!!_i
_
i
ii
i
/
_ii
2.0 AS rev 1.2.indd
8-9
_
YLON
NUT(E)
Qty:4
BOLT (B)
_
ARCWASHER (D)
95 mm
_
Qty:12
Qty:4
BOLT(F) _
LARGE"O" RING
_25mm
Qty:l
V)
Qty:4
ARC WASHER
(D)
CENTER
SUPPORT F RAME
SEAT
WELDMENT SET
\
\
ARC WASHER
(D)
NYLON NUT
(E)
UPPER PULLEY
ASSEMBLY
ARC WASHER
(D)
(A)
...... _.
LEFT SUPPORT
FRAME
RIGHT
SUPPORT
/FRAME
SEAT
ADJUSTMENT
/
PIN
t
SEAT SAFETY PiN
A
B
C
D
E
F
G
OpenHARDWARE B AGZ
Slide LARGE"0" RING
onto CENTER SUPPORT
FRAMEas shown in
diagram.
Attach U PPERPULLEY
ASSEMBLYtoCENTER
SUPPORTFRAME using
4 BOLTS (F) and 4 ARC
WASHERS (D). Tighten
this hardware.
Attach UPPER PULLEY
ASSEMBLY t o RIGHT
MAINSUPPORT F RAME
using 2 BOLTS (B), 4
ARC WASHERS (D) and 2
NYLON NUTS (E).
Attach U PPERPULLEY
ASSEMBLYto LEFT
SUPPORTFRAME using
2 BOLTS(B), 4 ARC
WASHERS (D),and 2
NYLON NUTS (E).
Install SEATWELDMENT
SETonto posts on
CENTER SUPPORT FRAME
as shown in diagram, and
insert SEATSAFETY PIN.
Install SEAT AD]USTMENT
PIN into SEATWELDMENT
SETas shownin
diagram. (Fullythread
into SEAT WELDMENT
SETafter SEAT BOTTOM
AD]USTMENT BARis
installed.)
(_
FLAT
WASHER (C)
Qty:10
BOLT (H)
20 mm
Qty: 4
NYLON
BOLT (F)
NUT(E)_
25 mm
Qty:2
Qty:2
(_
FLAT
WASHER ( I)
Qty:2
BOLT(G)_
NYLON
92mm
_NUT(K)
Qty:l
Qty:1
BOLT (J)
_
LOCK
83 rnrn
_
WASHER (L)
Qty:2
Qty:2
RADIAL A RM ASSEMBLY
CENTER
SUPPORT-_
FRAME
FLATWASHER
NYLONNUT(E)
NYLONNUT(K) \
NYLON NUT(E) \o.
CENTER
CONNECTION
TUBE
LEFT
CONNECTION
--/
TUBE
BOLT(J)
BOLT(J)
LEGROLLER _
BOLT(G)
SUPPORTTUBE
FLAT WASHER (1)
FLAT
LOCK
WASHER(C)WASHER(L)
RADIAL A RM
ASSEMBLY
(c)
(H)
"-_..
RIGHT CONNECTION TUBE
LOWER
CONNECTION TUBE
A OpenHARDWARE BAG3.
B Remove STOPPER from front side of RADIAL ARMASSEMBLY a nd reinstaflon back side.
Tightenboth STOPPERS.
C Attach RADIAL ARMASSEMBLY t o CENTER SUPPORT F RAME using 2 BOLTS (F), 2 LOCK
WASHERS (L) and 2 FLATWASHERS (C). Tightenthis hardware.
D Attach RIGHT SIDECONNECTION
TUBE to SEAT WELDMENT SETand to LOWER
CONNECTION
TUBE using 2 BOLTS (H) and 2 FLATWASHERS (C),as shownin diagram.
E Repeaton left side.
F Attach CENTER CONNECTION
TUBE to SEAT WELDMENT SETand to LOWER CONNECTION
TUBE using 2 BOLTS (1),4 FLATWASHERS (C)and 2 NYLON NUTS (E).
G Attach LEG ROLLER SUPPORT T UBE to LOWER CONNECTION TUBE using 1 BOLT (G),2
FLATWASHERS (I) and 1 NYLON NUT(K). Tightenall hardwarein Step3.
/
i(i
/
12/28/07
10:15:56
AM