Hideaway Concelo Інструкція з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Кухонна техніка Hideaway Concelo. Hideaway Concelo 4 сторінки.

Друкувати сторінку

Collar Rear

Panel

Collar Side Sub Assembly

PLEASE WATCH THE INSTALL VIDEO BEFORE YOU BEGIN

Step 1 – Unpack carton

• Unpack collar rear panel and place to one side.

• Remove lid pack place to one side.

• Remove buckets / trays and place to one side.

Step 2 – Pre-drill door panel

• If drilling the door panel using a CNC machine, drilling

positions are available as a CAD file from the Hideaway

Bins website.

• If drilling manually, refer to drilling template or drilling

dimensions.

• Mark a vertical centreline on the rear of the door panel.

• Mark a horizontal line indicating the top of the bin

body top reference. TIP: An allowance needs to be made

for the door overlap with the top of the carcase e.g. for a

16mm thick carcase material and 3mm gap between the

door panel and the bench top the horizontal line should be

(16-3) = 13mm down from the top edge of the panel.

• Align the door panel template with the lines as indicated

and mark the position of the mounting holes for the door

brackets through the paper. TIP: 3 screw locations

are required for each door bracket. An alternative location

for the top screw is indicated. This should only be used in

framed door situations but makes door adjustment more

difficult.

• Drill a 2mm pilot hole at each of the mounting locations.

(link on the cover of these instructions)

Step 3 – Install collar side sub assemblies

Refer to Fig. 1

3.1 - Position collar side sub assemblies

3.2 - Secure each using 12mm Surefix screws provided

Step 4 – Install collar rear panel on to collar sides

Refer to Fig. 1

4.1 - Position collar rear panel as shown.

4.2 - Secure using 6G x 12mm self tapping screws.

NOTE: do not use impact driver

Step 5 – Install body sub assembly

Top and side mounting is recommended when possible, and

mandatory for commercial use.

Option 1 - Body installation, top or top and side mount:

For new kitchens, where possible, it is easiest to place the

carcase upside down on a bench while installing the body.

See drilling dimensions on back of door drilling template.

• Mark Centreline in top of carcase

• Mark 2 central top mount holes and drill 2mm pilot holes.

• Position body in carcase and secure using 2 of the 16mm

Surefix screws provided. TIP: Align the front edge of the

body with the front of the carcase. If retrofitting the

unit in an existing kitchen clamp the body to the top of the

carcase to hold it in place while securing fasteners.

• Drill pilot holes in other selected mounting locations using

the body as a guide

• Insert and tighten 16mm Surefix screws in selected

mounting locations.

• If the carcase is upside down return it to an upright

position.

Option 2 - Body installation, side mount only:

Where possible partial top mounting to a rail in addition to

side mounting is recommended.

• Mark out all side mount holes referring to dimensions

provided on back of door drilling template. TIP: The centre

line of the side mount holes must be level to ensure the

product is level when installed.

• Predrill pilot holes for all 8 side mount holes.

• Position body in carcase and secure using 4 of the 16mm

Surefix screws provided for each side.

Step 6 – Assemble collar and door panel to runners

• Position collar assembly as shown in fig.4. TIP: Ensure that

runners are pulled forward, there is a black tab at the front

of the runner that can be pulled while holding the door

panel.

• Lower the door panel until a click is heard. TIP: The door

panel may need to be pushed down slightly

• Close the product and check that it is approximately level.

TIP: If the door panel is significantly out of level it may

indicate that it is not clipped down fully on one side.

Step 7 – Adjust the door panel position

• Refer to Fig. 5

• Loosen the 6 door bracket bolts using the 4mm Allen key

provided.

• Adjust the door to be square and parallel to carcase and in

the correct vertical position using the adjustment cams.

• Tighten the 6 door bracket bolts.

• Loosen the 6 door mounting screws and adjust the

horizontal position of the door panel.

• Tighten the 6 door mounting screws.

Continue overleaf...