AutomationDirect SOLO SL4848-LV Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Регулятор температури AutomationDirect SOLO SL4848-LV. AutomationDirect SOLO SL4848-LV 4 сторінки.
SOLO
Quick Start Guide
Quick Start Guide
Quick Start Guide
Quick Start Guide
Quick Start Guide
SOLO Temperature Controller
SL4848 Series
2015-04-20
5011654407-S447
This Quick Start Guide provides basic information on setting up the SOLO temperature controller. For
advanced setup and communication control as well as free configuration software visit the
AutomationDirect web site at www.AutomationDirect.com.
Product Support and Configuration Software
• For product support, specifications, and installation troubleshooting, a complete
User Manual can be downloaded from the On-line Documentation area of the
utomationDirect web site.
• For additional technical support and questions, call our Technical Support team
@ 1-800-633-0405 or 770-844-4200.
• Configuration software for the SOLO controller is available for free down-
load at www. utomationDirect.com. The software allows communication
and programming for up to four controllers at the same time. Parameters,
process values, set points and temperature changes can be monitored with
the software. The setup data can be uploaded to the user's PC via RS-485
communication. The user can monitor the temperature changes of the
controllers from the "PV Monitor" Display.
1
Safety Information
WARNING: To minimize the risk of potential safety problems, you should follow all applicable local and
national codes that regulate the installation and operation of your equipment. These codes vary from area to
area and it is your responsibility to determine which codes should be followed, and to verify that the equip-
ment, installation, and operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and
standards. We do not guarantee the products described in this publication are suitable for your particular appli-
cation, nor do we assume any responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or operation of this equipment, or if you need additional
information, please call us at 1-800-633-0405 or 770-844-4200.
This publication is based on information that was available at the time it was printed. At
Automationdirect.com® we constantly strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time without notice and without obligation. This
publication may also discuss features that may not be available in certain revisions of the product.
WARNING! Electric shock danger
1. To prevent electric shock, do not touch the AC terminals while the power is supplied to the controller.
This controller is an open-type temperature controller. Make sure to evaluate any dangerous application in
which a serious human injury or serious property damage may occur.
1. Always use recommended solder-less terminals: Fork terminal with insolation (M3 screw, width is 7.0mm, hole
diameter 3.2mm). Screw size: M3 x 6.5 (With 6.8 x 6.8 square washer). Recommended tightening torque: 0.4 Nm
(4kgfcm). Applicable wire: Solid/twisted wire of 2 mm, 12AWG to 24AWG. Choose AutomationDirect part numbers
BM-00120, BM-00220 or BM-00320 depending on wire size. Be sure to tighten them properly.
2. Protect the controller from dust or foreign objects to prevent controller malfunction.
3. Do not modify or disassemble the controller.
4. Do not connect anything to the "Not used" terminals.
5. Make sure all wires are connected correctly.
6. Do not install and/or use the controller in places subject to: (a) Dust or corrosive gases and liquid (b) High humidity
(c) Vibration and shock (d) EMI / RFI (e) high temperature.
7. Turn power off when wiring or changing a temperature sensor.
8. Be sure to use wires that match the thermocouple types when extending or connecting the thermocouple wires.
9. Use wires with correct resistance when extending or connecting a platinum resistance thermometer (RTD).
10. Keep the wire as short as possible when wiring a platinum resistance thermometer (RTD) to the controller and
route power wires as far as possible from load wires to prevent interference and induced noise.
11. This controller is an open-type unit and must be placed in an enclosure away from high temperature, humidity,
dripping water, corrosive materials, airborne dust and electric shock or vibration.
12. Make sure power cables and signals from instruments are all installed properly before energizing the controller,
otherwise serious damage may occur.
13. To prevent electric shock, do not touch the terminals in the controller or try to repair the controller when power is
applied.
14. Use a soft, dry cloth to clean the controller. Do not use acid or alkaline liquids for cleaning.
15. This instrument is not furnished with a power switch or fuse. Therefore, if a fuse or power switch is required, install
the protection close to the instrument. Recommended fuse rating: Rated voltage 250 V, Rated current 1 A. Fuse
type: Time-lag fuse
16. Note: This controller does not provide overcurrent protection. Use of this product requires that suitable overcur-
rent protection device(s) must be added to ensure compliance with all relevant electrical standards and codes.
(Rated 250 V, 15 Amps max). A suitable disconnecting device should be provided near the controller in the end-
use installation.
All manuals and user guides at all-guides.com
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
5
2
General Description
AutomationDirect's SOLO is a single loop dual output temperature controller that can control both heating and
cooling simultaneously. There are four types of control modes: PID, ON/OFF, Manual, and Ramp / Soak control.
Depending upon the particular model of controller, the available outputs include relay, voltage pulse, current, and
linear voltage. There are up to three alarm outputs available to allow seventeen alarm types in the initial setting
mode. SOLO can accept various types of thermocouple, RTD, or analog inputs, and has a built in RS-485 inter-
face using Modbus slave (ASCII or RTU) communication protocol.
Other features include:
• 1/16 DIN panel size
• 2 line x 4 character 7-segment LED display for Process Value (PV): Red color, and Set Point (SV): Green color
• Auto Tuning (AT) function with PID control
• Selectable between °C and °F for thermocouple or RTD inputs
• 0 to 50 °C (32 to 122 °F) operating temperature range
• UL, CUL and CE agency approvals
3
Specifications
Specifications
Input Power Requirements
Operation Voltage Range
Power Consumption
Memory Protection
Control Mode
Input Accuracy
Less than ± 0.2% full scale (except thermocouple R, S, & B types) Max ± 3° (thermocouple R, S, & B types)
Vibration Resistance
10 to 55 Hz, 10 m/s
Shock Resistance
Max. 300 m/s
Ambient Temperature Range
Storage Temperature Range
Altitude
Relative Humidity
RS-485 Communication
Transmission Speed
IP65: Complete protection against dust and low pressure spraying water from all directions.
IP Rating
Agency Approvals
Degree 2 - Normally, only non-conductive pollution occurs.
Pollution Degree
Temporary conductivity caused by condensation is to be expected.
Input Types
• Thermocouple*
K, J, T, E, N, R, S, B, L, U, TXK (Sampling Rate: 400 ms / per scan)
• Platinum RTD
3-wire Pt100, JPt100 (Sampling Rate: 400 ms / per scan)
• Analog
0-50 mV, 0-5V, 0-10V, 0-20 mA*, 4-20 mA* (Sampling Rate: 150 ms / per scan)
Control Output Options
• Relay (R)
• Voltage Pulse (V)
• Current (C)
DC 4-20 mA output (Load resistance: Max 600
• Linear Voltage (L)
*Note: Use only ungrounded thermocouples.
*Note: The supplied 249 ohm resistor should be installed as shown in the terminal wiring diagrams
in section 7 for current input operation.
Output Specifications
Part Number
Input Voltage
Output #1
SL4848-RR
100 - 240 VAC
Relay - SPST
SL4848-VR
100 - 240 VAC
Voltage Pulse
SL4848-CR
100 - 240 VAC
Current
SL4848-LR
100 - 240 VAC
Linear Voltage
SL4848-RR-D
24 VDC
Relay - SPST
SL4848-VR-D
24 VDC
Voltage Pulse
SL4848-CR-D
24 VDC
Current
SL4848-VV
100 - 240 VAC
Voltage Pulse
SL4848-CV
100 - 240 VAC
Current
SL4848-LV
100 - 240 VAC
Linear Voltage
*Output #2 can be configured as control output #2 or as Alarm #3
**Alarm #1 and Alarm #2 have a shared common
4
Box Contents and Unpacking Instructions
• Unpack the SOLO temperature controller from its shipping carton. Included in the carton is the temperature
controller, mounting brackets plus hardware and this Quick Start Guide.
• Inspect all equipment for completeness. If anything is missing or damaged, immediately call the
utomationDirect returns department @ 1-800-633-0405.
• Inspect the part number to ensure the model received matches the output type required.
5
Controller and Panel Cutout Dimensions
SOLO
4848
PV
C
F
SV
AT
OUT1
OUT2
ALM
SET
1.89"
0.37"
3.15"
(48.0 mm)
(9.5 mm)
(80.0 mm)
100 to 240 VAC 50 / 60 Hz or 24 VDC
85 to 264 VAC or 21.6 to 26.4 VDC
5 VA Max
EEPROM 4K bit, number of writes 100,000
PID, ON/OFF, Ramp / Soak control or Manual
2
for 10 min, each in X, Y and Z directions
2
, 3 times in each 3 axes, 6 directions
32°F to 122°F (0°C to 50°C)
-4°F to 149°F (-20°C to 65°C)
2000m or less
35% to 80% (non-condensing)
Modbus slave ASCII / RTU protocol
2400, 4800, 9600, 19.2K, 38.4K bps
(inside suitable enclosure)
UL, CUL, CE (UL file number E311366)
SPST max. resistive load 5A @ 250 VAC
DC 14V Max, output current 40mA Max
)
DC 0-10V (Load resistance Min 1K )
Output #2 / Alarm #3*
Alarm #1**
Alarm #2**
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Relay - SPST
Voltage Pulse
Relay - SPST
Relay - SPST
Voltage Pulse
Relay - SPST
Relay - SPST
Voltage Pulse
Relay - SPST
Relay - SPST
Mounting Brackets
and Hardware
SL4848 Temperature
Controller
SL4848
249 ohm resistor
Quick Start Guide
2.56"
(Min.)
[65.0 mm]
1.77"
[45.0 mm]
+0.02
1.77"
-0
[45.0 mm]
+0.6
-0
+0.02
-0
+0.6
-0