DBI SALA PYTHON SAFETY 1500096 Інструкції з монтажу та використання і попередження

Переглянути онлайн або завантажити pdf Інструкції з монтажу та використання і попередження для Засоби безпеки DBI SALA PYTHON SAFETY 1500096. DBI SALA PYTHON SAFETY 1500096 2 сторінки. Scaffold wrench holster with retractor

Друкувати сторінку
TM
Fall Protection for Tools
TM
Installation and Use Instructions for
Python Safety Scaffold Wrench Holster
with Retractor
This manual is intended to be used as part of an employee training program.
These products are not to be used for worker fall protection.
1500096
1500097
Model #
1500096
Scaffold Wrench Holster with Retractor
Scaffold Wrench Holster with Retractor
1500097
and Hook2Loop Bungee Tether
www.capitalsafety.com
Form: 5903847-A3 Rev: A
© Copyright 2015, DB Industries, Inc.
1
2
3
4
EN
Python Scaffold Wrench Holster with Retractor
•
Beacon™ High Visibility Reflectors on front and back.
•
Quickly holsters scaffold wrenches while working at height.
•
D-Rings on sides of Wrench Holster are load-rated for 5 lbs (2.3kg).
•
Back of Holster has pouch for Python Safety Retractor.
Retractor is load-rated for 1.5 lbs (0.7 kg) and extends up to
52 in. (132.1cm). Rear feed system keeps Retractor out of the way.
•
Holster and Hook2Loop Bungee Tether combination (1500097) can be used
to tie off scaffold wrenches.
ü
When to use a Scaffold Wrench Holster with Retractor
•
To maintain positive control of scaffold wrenches while working at height.
û
When NOT to use a Scaffold Wrench Holster with Retractor
•
Do not use tools that exceed D-Ring or Retractor load limits.
Warnings
•
All warnings, warning labels and instructions should be read and
understood before using this product. Failure to do so may result in
property damage, serious injury or death.
•
All procedures shown in this instruction are for Python Safety products
only.
•
Python Safety attachment points require the use of an appropriate
Python Safety Lanyard, Tether or Retractor for safe connection of
the tool or equipment to another Python attachment point, the user
or an anchorage. See specific Python Safety instructions for product
installation, connection and use procedures.
•
Do not use for worker fall protection or for climbing.
•
Do not use if fall protection for tool components will interfere with the
safe working condition or operation of the connected tool or equipment.
•
If a tool is dropped or a load is forced onto the connection point,
inspect the tool and fall protection for tool components
connected to the tool for damage. This includes the attachment
point, the lanyard and the anchor point. (Anchor point examples: tool
holster, tool belt, tool bag, worker safety harness or anchor point such
as a rail.) Look for torn stitching and for deformities and damage to any
material. If damage is found, remove the affected items from service
immediately and replace them.
•
Inspect before, during, and after use to ensure fall protection for tool
components are in good working condition and free from defects, cuts,
tears, etc. See "Inspect Before Use" in this instruction manual. Never
modify Python Safety products.
•
Never exceed the maximum load rating stated on the Python Safety
product label.
•
Never connect individual tools that weigh more than 5 pounds (2.26 kg)
to a person.
•
Never attach tool lanyards or attachment points to a tapered surface.
•
Never wrap fall protection for tool components around rough or sharp
edges.
•
Never attach multiple fall protection for tool components together (daisy
chain).
•
Never make a modification to a connected tool or equipment that will
cause it to deviate from the manufacturer's specification.
•
Always use proper personal protective equipment (PPE).
•
Use extreme caution while working around rotating or moving
equipment.
•
To avoid the danger of electrical shock, use extreme caution when
working around power equipment and connections.
•
Read and understand product information and warning labels for all
connecting lanyards and adapters.
•
All connected tools and equipment must be properly maintained and
inspected for defects or deterioration before each use.
Inspect Before Use
Python Safety equipment and components must be thoroughly inspected
before, during and after each use. Any fall protection for tools component
that has deformities, unusual wear or deterioration must be immediately
removed from service and replaced. Inspect the entire surface of the
component, carefully rotating it while visually inspecting for damage or wear
that might affect its usefulness and dependability. Inspect material and
stitching, hardware, D-Rings and fasteners. Confirm that carabiners, trigger
snaps, retractors and other connectors operate properly.
How to use the Scaffold Wrench Holster with Retractor:
1.
Insert user's belt through the Retractor Holster belt loops.
2.
The Python Safety Steel Cable Retractor feeds through the rear of the
holster. Connect to the scaffold wrench by threading the Quick Ring
attached to the yoke at the end of the Retractor Cable through the pre-
drilled hole in the end of the wrench.
The connected scaffold wrench can not exceed 1.5 lbs (0.7 kg) when
using the Retractor.
How to use the Scaffold Wrench Holster with Hook2Loop Bungee
Tether (1500097):
3.
Scaffold wrenches that weigh more than 1.5 lbs (0.7 kg) but less than 5
lbs (2.3kg) can be tethered to the Scaffold Wrench Holster 1500097 by
using the included Hook2Loop Bungee Tether. Connect the loop end of
the Tether to the scaffold wrench with the included Quick Ring. Pass the
carabiner end of the Tether through the loop and pull tight to cinch the
Tether on the Quick Ring. Connect the carabiner to one of the Holster
D-Rings.
If the pre-drilled hole in the end of the wrench is large enough, the
Tether can be connected to the wrench handle without the use of the
Quick Ring. Feed the loop end of the Tether through the hole. Pass the
carabiner end of the Tether through the loop and pull tight to cinch
the Tether on the handle. Connect the carabiner to one of the Holster
D-Rings.
4.
When the scaffold wrench is not in use, the hook and loop strap can be
closed to secure the wrench in the Holster. When the scaffold wrench is
in use, the strap can be locked in an open position for easy holstering
and un-holstering of the wrench.
After Use
After use, clean the Holster, Retractor and connected tool or equipment to
remove dirt, corrosives or contaminants. Remove surface dirt with a wipe that
has been moistened with a mild solution of water and soap or detergent. Work
into a thick lather and clean the item. Wipe with a clean cloth and hang to dry
away from excessive heat, steam, or sunlight.
Store in a clean and dry environment, free from fumes or corrosive elements.
Proper care of safety equipment helps to ensure that it will operate effectively
and to extend its service life.
In Case of a Dropped Tool
•
If a tool is dropped or a load is forced onto the connection point,
inspect the tool and fall protection for tool components
connected to the tool for damage. This includes the attachment
point, the lanyard and the anchor point. (Anchor point examples: tool
holster, tool belt, tool bag, worker safety harness or anchor point such
as a rail.) Look for torn stitching and for deformities and damage to any
material. If damage is found, remove the affected items from service
immediately and replace them.
•
Incidents should be reported to your safety coordinator.