Hifionics Zeus ZXI80.4 Посібник користувача - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник користувача для Автомобільний підсилювач Hifionics Zeus ZXI80.4. Hifionics Zeus ZXI80.4 14 сторінок.

Друкувати сторінку

AMPLIFIER FEATURE DESCRIPTIONS

ZEUS ZXi AMPLIFIERS:

Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation

except the 5 channel which is capable of 1-Ohm on channel 5.

The input sensitivities for rated output powers are variable from 0.2 volts to 6 volts.

All crossovers are fully variable in their respective ranges.

Crossover filters are 12dB/Octave.

A POWER LED indicates the powered up and turned on condition.

All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,

and amplifier DC faults indicated by the red "PROTECT" LED.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting

simplifying daisy chaining of amplifiers.

-HP: Selects the built in HIGH PASS filter, variable from 10Hz to 15kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LP/BP: Selects the built in LOW PASS , variable from 30Hz to 150Hz.

BASS EQ: Fixed 45Hz bass boost variable from 0dB to 10dB.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of

controls.

1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch. Switch to 2 channel if you only have 1 set of

RCA's in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 4 channel if you

are providing RCA's to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting

simplifying daisy chaining of amplifiers.

-HP: Selects the built in HIGH PASS filter, variable from 10 Hz to 15kHz.

-FULL: Bypasses all crossovers for full frequency range operation.

-LP/BP: Selects the built in LOW PASS , variable from 30 Hz to 150Hz.

BASS EQ: Fixed 45Hz bass boost variable from 0dB to 10dB.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

The ZXi60.4+1K has three sets of inputs:

Line inputs on RCA jacks for channel pairs 1&2, 3&4, and MONO channel 5. These inputs can be used in

various combinations, to suit the application, depending on the settings of the INPUT MODE switch, and

the X-OVER switches for channels 1&2, and channels 3&4, respectively.

INPUT MODE slide switch:

- In the CH2 position, ALL five amplifier inputs are selected from the CH1/CH2 RCA jacks. Channel 5

receives a mono mixed signal.

- In the 4CH position, channel pair 1&2 receive input signal from RCA jacks CH1 and CH2, and channel

pair 3&4 receive input signal from RCA jacks CH3 and CH4. A mono mixed signal from these four RCA

jacks are also fed to channel 5.

- When 5CH DISCRETE is selected, each channel receives an input signal from its respective input RCA

jack. Channel 5 has two jacks on its LINE INPUT, which are summed together.

CH1/2 X-OVER slide switch:

- HI: Selects the HIGH PASS filter, variable from 10Hz to 15KHz.

- FULL: Sets this pair to full range operation.

CH3/4 X-OVER slide switch:

- HI: Selects the HIGH PASS filter, variable from 10Hz to 15KHz.

- FULL: Sets this pair to full range operation.

-LP/BP: Selects the built in LOW PASS , variable from 30 Hz to 150Hz.

CH 5:

- The channel 5 functions were chosen to be very specific to mono bass operation, and not switchable:

- The LOW PASS filter has a variable range from 30 Hz to 150 Hz.

- The BASS EQ gives a bass boost, 0 to +10 dB, at 45 Hz.

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU

WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE

WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4

and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The 5 channel amp is capable of 4,

2 and 1-Ohm operation on the 5th channel ONLY.

ZXi200.2 2-CHANNEL AMPLIFIERS

LINE INPUT

HI PASS

X-OVER

10Hz 15KHz

REMOTE

HP FULL LP/BP

Note that the LOW PASS signal is MONO.

-In the LP/BP position, the HIGH PASS filter acts as a

subsonic filter.

-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,

BASS EQ is also switched in.

ZXi40.4 / ZXi80.4 / ZXi150.4 4-CHANNEL AMPLIFIERS

LINE INPUT

REMOTE

HI PASS

CH1/2 CH3/4

10Hz-15KHz

HI FULL LP/BP

HI PASS

CH2-CH4

10Hz-15KHz

HI FULL LP/BP

MODE

Note that the LOW PASS signal is MONO.

-In the LP/BP position, the HIGH PASS filter acts as a

subsonic filter.

-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,

BASS EQ is also switched in.

ZXi60.4+1K 5-CHANNEL AMPLIFIERS

CH1/2

LINE INPUT

HI PASS

LEVEL

X-OVER

HI FULL

CH3

CH1

10Hz 15Khz

CH4

CH2

30Hz 150Hz

0dB-10dB

REMOTE

LOW PASS

BASS EQ

LINE OUT

LOW PASS

BASS EQ

LEVEL

POWER

30Hz 150Hz 0dB 10dB 6V 0.2V

PROTECT

1/2 CH

LOW PASS

BASS EQ

LEVEL

POWER

LINE OUT

X-OVER

30Hz-150Hz 0dB-10dB

6V 0.2V

PROTECT

3/4 CH

LOW PASS

BASS EQ

LEVEL

X-OVER

30Hz-150Hz 0dB-10dB

6V 0.2V

CH3/4

X-OVER

LOW PASS

LEVEL

HI PASS

HI FULL BP

0.2V

10Hz 15Khz

30Hz 150Hz

6V 0.2V

5CH

POWER

6V 0.2V

Ch2 Ch4 Ch5

LEVEL

PROTECT

MODE