Dynamite Prophet DYNC2040 Інструкція з експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Зарядний пристрій Dynamite Prophet DYNC2040. Dynamite Prophet DYNC2040 8 сторінок. Sport quad 4x50w ac/dc battery charger
Друкувати сторінку
ONLy NI-Mh IS ShOWN IN ThE FOLLOWINg ThrEE SECTIONS.
5 - NICKEL (NI-Mh/NI-CD) ChArgINg
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Esc / Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.
PROGRAM SELECT
NiMH Battery
4. Press the Start / Enter button.
5. Press the Dec or Inc Button until Ni-MH/Ni-Cd CHARGE appears.
NiMH CHARGE Man
CURRENT
1.0A
6. Press the Start / Enter Button to edit the parameter.
7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.
8. The charger will check the battery and charger settings and charging will begin.
9. Press the Dec or Inc Button to see the rest of the Discharging information.
10. Press Esc / Mode at any time to stop discharging.
11. When discharging is complete, the charger will sound a series of beeps.
12. Disconnect the battery from the charge adapter.
6 - NICKEL DISChArgINg
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.
NiMH DISCHARGE
1.0A
12.0V
4. Press the Start / Enter button.
5. Press the Dec or Inc Button until Ni-MH/Ni-Cd DISCHARGE appears.
6. Press the Start / Enter Button to edit the parameter.
7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.
8. The charger will check the battery and charger settings and charging will begin.
9. Press the Dec or Inc Button to see the rest of the Discharging information.
10. Press Esc / Mode at any time to stop discharging.
11. When discharging is complete, the charger will sound a series of beeps.
12. Disconnect the battery from the charger.
7 - NICKEL CyCLE ChArgINg
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Ni-MH/Ni-Cd.
4. Press the Start / Enter button.
5. Press the Dec or Inc Button until Ni-MH/Ni-Cd DCHG>CHG appears.
C=1.0A D=1.0A
1
6. Press the Start / Enter Button to edit the parameter.
7. Once the parameters are at the desired settings including how many cycles (A), press and hold
the Start / Enter button for 3 seconds.
8. The charger will check the battery and charger settings and charging will begin.
9. Press the Dec or Inc Button to see the rest of the Cycle information.
10. Press Esc / Mode at any time to stop discharging.
11. When discharging is complete, the charger will sound a series of beeps.
12. Disconnect the battery from the charger.
CAUTION: The Pb charge program menus are to be used ONLY for the charging and
discharging of Pb battery packs. Charging other battery types using the Pb charge
programs will damage the battery or the charger.
8 - PB ChArgINg
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Pb BATT.
PROGRAM SELECT
Pb Battery
4. Press the Start / Enter button.
5. Press the Dec or Inc Button until Pb CHARGE appears.
Pb CHARGE
0.1A
4.9V (2P)
6. Press the Start / Enter Button to edit the parameter.
7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.
8. The charger will check the battery and charger settings and charging will begin.
9. Press the Dec or Inc Button to see the rest of the charging information.
10. Press Esc / Mode at any time to stop discharging.
11. When charging is complete, the charger will sound a series of beeps.
12. Disconnect the battery from the charger.
TrOUBLEShOOTING
During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger's LCD screen, make the recommended responses. If the message continues
after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.
REVERSE POLARITY
Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery.
PROCESS INTERRUPTED
Make sure the power connections are correct for charging.
OUTPUT SHORT CIRCUIT
Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.
INPUT VOLTAGE ERROR
Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct input voltage.
CHARGER FAILURE
Charger electronics require repair.
BATTERY LOW VOLTAGE
Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
BATTERY HIGH VOLTAGE
Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL LOW VOLTAGE
Cell voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL HIGH VOLTAGE
Cell voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
CELL CONNECT ERROR
Make sure the balance connection is correct for charging.
CHARGER OVERHEATING
Charger temperature is too high. Power OFF the charger and let it cool.
OVER POWER
Input voltage to the charger exceeded the default or adjusted input voltage setting. Make sure the power source for the charger provides the correct input voltage.
MAX CURRENT
Current is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
SAFETY TIMER
Maximum safe time limit has been reached.
MAX CAPACITY
Maximum capacity limit has been reached.
MAX EXT. TEMP
External temperature is too high. Let charger and battery cool.
CONNECTION BREAK
Make sure the battery pack is connected to the charger.
© 2015 Horizon Hobby, LLC. Dynamite, Prophet and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC.
9 - PB DISChArgINg
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Esc/Mode Button to scroll through the main menu screens until you reach Program
Select=Pb BATT.
4. Press the Start / Enter button.
5. Press the Dec or Inc Button until Pb DISCHARGE appears.
Pb DISCHARGE
1.0A
4.9V (2P)
6. Press the Start / Enter Button to edit the parameter.
7. Once the parameters are at the desired settings, press and hold the Start / Enter button for 3
seconds.
8. The charger will check the battery and charger settings and discharging will begin.
9. Press the Dec or Inc Button to see the rest of the Discharging information.
10. Press Esc / Mode at any time to stop discharging.
11. When discharging is complete, the charger will sound a series of beeps.
12. Disconnect the battery from the charger.
10 - DIgITAL POWEr
The Digital Power menu enables you to use the Prophet Sport Quad charger as a power supply for
external devices. The maximum Digital Power output for this charger is 6A / 24V.
1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected
charge port (A, F), making sure that the positive and negative connectors are not reversed.
2. Press the Esc / Mode Button to scroll through the main menu screens until you reach Digital
Power.
PROGRAM SELECT
Digital Power
3. Press the Start / Enter Button to edit the parameter.
4. Once the parameters are at the desired settings, press and hold the Start / Enter Button for 3
seconds.
5. Press the Esc / Mode Button at any time to stop supplying power to the external device.
6. Disconnect the external device from the charger.
11 - MEMOry SAVE
The Memory Save menu option enables you to save 10 (x4) battery charging profiles that you use
most often.
1.
Press the Esc / Mode Button to scroll through the main menu screens until you reach
Program Select - Memory Save.
PROGRAM SELECT
Memory Save
2.
Press the Start / Enter Button to enter the Memory Save menu. The first time you enter the
menu, the "0" model memory location flashes.
3.
Press the Dec or Inc Button to select a memory location (0-9), then press and hold the
Start / Enter Button to save the selection. The BATT TYPE screen appears.
4.
Press the Dec or Inc Button to select the desired battery type, then press the Start / Enter
Button.
5.
Press the Inc Button to adjust the parameters for Balance Charge, Cycle, Storage, etc.
6.
Press and hold the Start / Enter Button for 3 seconds to save your selections. The charger
screen displays "Saving..", then returns to the Memory Save screen.
MEMORY NiMH
[1]
AUTO
1.5A
A
12 - LOAD DATA
The Load Data menu option enables you to access the 10 battery charging profiles that you stored
in the Save Data menu.
1.
Press the Esc / Mode Button to scroll through the main menu screens until you reach
Program Select - Load Data.
PROGRAM SELECT
Memory Load
2.
Press the Start / Enter Button to enter the Load Data menu. The first time you enter the
menu, the "0" model memory location flashes.
3.
Press the Dec or Inc Button to select a memory location (0-9).
4.
Press the Start / Enter Button for 3 seconds until the Charge screen appears.
5.
Press the Dec or Inc Button to scroll through Charge, Balance Charge, Cycle, Discharge,
Storage, etc.
6.
Press and hold the Start / Enter Button for 3 seconds to load the desired function.
MEMORY NiMH
[1]
AUTO
1.5A
13 -PrOgrAM SELECT – USEr SET
1. Press the Esc / Mode Button to scroll through the main menu screens until you reach Program
Select = User set.
PROGRAM SELECT
User Set
=>
2. Press the Start / Enter button to enter the User Set menu.
3. Press the Dec or Inc Button to scroll through the menu.
4. Press the Start / Enter Button to edit the parameter.
5. Press the Dec or Inc Button to increase or decrease the value.
6. Press the Start / Enter Button again to save the selection.
7. Press the Esc / Mode Button to return to the main menu.
A -PrE ChArgE TIME (NI-Mh/NI-CD BATTErIES ONLy)
If a Ni-MH or Ni-Cd battery is fully discharged, the battery charger may not detect the
battery. The Pre-Charge Time enables you to apply a low charge rate, increasing the battery
voltage to the point where the charger detects the battery.
PreCharge Time
ON/Off
1min
WArNINg: Never use the Pre-Charge Time with Li-Po batteries. Doing so may cause
the battery to catch fire.
B -WAIT TIME Chg>DChg DEFAULT IS 1 MINUTE
When you cycle a Ni-MH or Ni-Cd battery (charging, discharging and then charging again),
the battery will get very warm. The Wait Time interval between each step of the process
allows the battery to cool before starting the next step. Default time is 1 minute, but this
can be set between 0 and 60 minutes. Always allow the battery to cool to room temperature
before charging or discharging.
Wait Time
CHG>DCHG
5min
C -NIMh SENSITIVITy D. PEAK – DEFAULT
The D.Peak (Delta Peak) value is adjustable between 5mV/Cell and 20mV/Cell. 8mV/
Cell is a good starting point for Ni-MH batteries. If the Delta Peak value is too high, you
risk overcharging the battery; if the value is too low, charging will stop before the battery
reaches full capacity.
NiMH Sensitivity
D. Peak
Default
D -NICD SENSITIVITy D. PEAK – DEFAULT
The D.Peak (Delta Peak) value is adjustable between 5mV/Cell and 20mV/Cell. 10mV/
Cell is a good starting point for Ni-Cd batteries. If the Delta Peak value is too high, you
risk overcharging the battery; if the value is too low, charging will stop before the battery
reaches full capacity.
NiCd Sensitivity
D. Peak
Default
E -TEMP. CUT-OFF DEFAULT IS 80C/176F
The charger can be used in conjunction with a battery mounted temperature sensor (sold
separately, DYN5033) connected to the Temperature Sensor Port to monitor the temperature
of the battery during the charging process. If the battery temperature reaches the cut-off
limit, the charger will stop the charging process. Temperature values can be adjusted
between 20–80° C (68–176° F).
Temp. Cut-off
ON
80C(176F)
LIMITED WArrANTY
What this Warranty Covers - Horizon Hobby, LLC (Horizon) warrants to the original purchaser that
the product purchased (the "Product") will be free from defects in materials and workmanship at
the date of purchase.
What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic dam-
age, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due
to improper use, installation, operation or maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center,
(v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with ap-
plicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF
THE PURCHASER'S INTENDED USE.
Purchaser's remedy - Horizon's sole obligation and purchaser's sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon
to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WAR-
RANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEG-
LIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon
exceed the individual price of the Product on which liability is asserted. As Horizon has no control
over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted
for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all result-
ing liability. If you as the purchaser or user are not prepared to accept the liability associated with
the use of the Product, purchaser is advised to return the Product immediately in new and unused
condition to the place of purchase.
Law - These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WArrANTy SErVICES
Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup or use of the Product has been started,
you must contact your local distributor or Horizon directly. This will enable Horizon to better answer
your questions and service you in the event that you may need any assistance. For questions or
assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry
WArrANTY AND SErVIcE cONTAcT INFOrMATION
Country of Purchase
horizon hobby
Horizon Service Center
(Repairs and Repair Requests)
Horizon Product Support
United States of America
(Product Technical Assistance)
Sales
Service/Parts/Sales:
United Kingdom
Horizon Hobby Limited
Horizon Technischer Service
Germany
Sales: Horizon Hobby GmbH
Service/Parts/Sales:
France
Horizon Hobby SAS
Service/Parts/Sales:
China
Horizon Hobby – China
cOMPLIANcE INFOrMATION FOr ThE EUrOPEAN UNION
EU Compliance statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive
2004/108/EC and Low Voltage Directive 2006/95/EC. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user's responsibility to dispose of their waste equipment by handing it over to a designated collections point for
the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or where you purchased the product.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
F -SAFETy TIMEr DEFAULT IS ON, 240MIN
Use the Safety Timer menu to set a time limit for charging a battery. When a charge cycle is
started, a clock inside the charger will begin recording the elapsed charge time. If the safety
timer function has been turned ON, the charger will stop the charging process once this
time limit has been reached to avoid damage caused by overcharging the battery. This time
value can be set between 10 and 720 minutes, in 10 minute increments.
Safety Timer
ON/OFF
240min
g -CAPACITy CUT-OFF DEFAULT IS ON, 5000MAh
Use the Capacity Cut-Off menu to set a capacity limit on when the charger stops charging
a battery. When a charge cycle starts, the charger records the battery capacity. When the
capacity cutoff function is set at ON, the charger will stop charging at the capacity limit to
prevent battery damage. Capacity can be adjusted between 10 and 50,000mAh in 100mAh
increments.
Capacity Cut-Off
ON/OFF
5000mAh
h -INPUT POWEr LOW CUT-OFF DEFAULT IS 11.0V
Use the Input Power Low Cut-Off menu to set the input voltage limit. An alarm will sound if
the input voltage falls below the cut-off value. The voltage alarm value can be set between
10.0 and 11.0V.
Input Power Low
Cut-Off
11.0V
I -KEy BEEP (DEFAULT ON) / BUzzEr (DEFAULT ON)
Use the Key Beep/Buzzer menu to set the key beep and charger alarm buzzer at ON or OFF
as needed. We recommend that you leave the alarm ON to alert you when charging is
complete or if there is cause for alarm during charging.
Key Beep
ON/OFF
Buzzer
ON/OFF
J -BACK-LIghT
Change the Back-Light brightness by pressing the Start / Enter button and then Press the
Dec or Inc Button to change the value.
Back–light
100%
K -BATTEry END VOLTAgE
Press Start / Enter Button to select the desired battery type. Change the Default end
voltage by pressing Dec or Inc.
Battery end volt
LiPo
4.20V/C
L -FACTOry rESET PrESS ENTEr > 2S
Press the Start / Enter button for more than 2 seconds to reset all charger values to the
default values.
Factory reset
Press Enter > 2S
at https://horizonhobby.quickbase.com/db/bghj7ey8c?a=GenNewRecord, or call the toll free tele-
phone number referenced in the Warranty and Service Contact Information section to speak with a
Product Support representative.
Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes may be
included, but are not designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request
is available at http://www.horizonhobby.com/content/_service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon, you will be asked
to provide your complete name, street address, email address and phone number where you can
be reached during business hours. When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to horizon. If you have any issue with a Li-Po
battery, please contact the appropriate horizon Product Support office.
Warranty requirements - For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been
met, your Product will be serviced or replaced free of charge. Service or replacement decisions are
at the sole discretion of Horizon.
Non-Warranty Service - Should your service not be covered by warranty, service will be
completed and payment will be required without notification or estimate of the expense
unless the expense exceeds 50% of the retail purchase cost. By submitting the item for ser-
vice you are agreeing to payment of the service without notification. Service estimates are available
upon request. You must include this request with your item submitted for service. Non-warranty
service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier's checks, as well as Visa, MasterCard, American
Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Hori-
zon's Terms and Conditions found on our website http://www.horizonhobby.com/content/_service-
center_render-service-center.
ATTENTION: horizon service is limited to Product compliant in the country of use
and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of the un-serviced
Product, through a carrier of the sender's choice and at the sender's expense. horizon
will hold non-compliant Product for a period of 60 days from notification, after which it
will be discarded.
Contact Information
Address
servicecenter.horizonhobby.com/RequestForm/
www.quickbase.com/db/
4105 Fieldstone Rd
bghj7ey8c?a=GenNewRecord
Champaign, Illinois, 61822 USA
888-959-2306
888-959-2306
Units 1–4, Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
+44 (0) 1279 641 097
Christian-Junge-Straße 1
25337 Elmshorn, Germany
+49 (0) 4121 2655 100
11 Rue Georges Charpak
77127 Lieusaint, France
+33 (0) 1 60 18 34 90
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
+86 (021) 5180 9868
Created 08/2015 | 48543