Galanz DWUK003W Інструкція з експлуатації - Сторінка 12
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Посудомийна машина Galanz DWUK003W. Galanz DWUK003W 14 сторінок.
Друкувати сторінку
Once the appliance has been installed, the power supply cable and the electrical socket should
be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced by the manufacturer or its service
center in order to prevent all potential hazards.(See Assistance)
The company shall not be held responsible for any incidents that occur if these regulations are
not observed.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before running the first wash cycle, completely
fill the salt dispenser with and add approximately 2 Kg of salt (see Rinse aid and refined salt). The
water may overflow: this is normal and is not a cause for concern. It is also normal that the LOW
SALT indicator light continues to flash for a few cycles after the salt has been loaded.
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and
the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and
drain hoses that can be positioned to the right or the left to facilitate proper installation.
Leveling the Appliance
Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the
dishwasher, making it level.
The appliance should not be inclined more than 2° in any instance.
NOTE:
The maximum adjustment height of the feet is 20 mm.
How to Drain Excess Water From Hoses
If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or a suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, ensure you to use a similar drain hose.
It must be no longer than 4 metres, otherwise the cleaning effect of the dishwasher could be
reduced.
Syphon Connection
The waste connection must be at a height of between 50cm (minimum) and 100cm (maximum)
from the bottom of the dish. The water drain hose should be fixed by a hose clip.
20
Start of Dishwasher
The followings should be checked before starting the dishwasher:
1 Whether the dishwasher is level and fixed
2 Whether the inlet valve is opened
3 Whether there is leakage at the connections of the conducts
4 Whether the wires are tightly connected
5 Whether the power is switched on
6 Whether the inlet and drain hoses are knotted
7 All packaging materials and printed matter should be taken out from the dishwasher
Attention
After installation, please store this manual for future reference.
9. Troubleshooting Tips
Error codes
If a problem occurs with your appliance error codes may display. Please refer to the following table
for possible causes.
Codes
E1
°.
E2
E3
E4
E5
E6
E7
E8
WARNING!
If overflow occurs, turn off the main water supply before calling the customer helpline. If there is water in the
base pan because of an overfill or small leak, the water should be removed before restarting the dishwasher.
Meanings
Possible Causes
The door is opened when the
Door open
dishwasher is operating
Water inlet
Water inlet malfunction
Water drainage malfunction
Water drainage
Temperature sensor
Temperature sensor malfunction
Overflow/leakage
Overflow occurs/Water leakage occurs
Water leakage occurs
Water leakage
Heating element
Abnormal heating
Water diversion system
Water diversion system malfunction
21