Hifonics XXV XXV Gemini Посібник користувача - Сторінка 7
Переглянути онлайн або завантажити pdf Посібник користувача для Підсилювач Hifonics XXV XXV Gemini. Hifonics XXV XXV Gemini 20 сторінок. Xxv edition high performance amplifier
FULL RANGE STEREO
This is the most basic application for the XXV Series 2 channel amplifiers.
1. Interconnect cable checklist:
Connect the LINE INPUTS to the Radio/CD with good quality RCA cables.
2. Crossover Switch:
The X-OVER switch must be in the FULL position.
3. Crossover frequency control checklist:
N/A for full range operation.
FULL RANGE
STEREO LINE INPUT
FULL RANGE MONO
This application illustrates the basic mono bridging method for all HiFonics
amplifiers.
Interconnect cable checklist:
A MONO signal source is required, such as would be available from the mono
sub bass output of an active crossover, whether standalone, or built into a head
Important:
unit or equalizer.
Do not be tempted to connect the hot, or positive
outputs, from any source together to obtain a mono signal, as this could very
well damage the output stage of that source.
It is necessary to feed the SAME signal to both left and right inputs via a
Y-adapter RCA cable.
Connect the mono speaker positive terminal to the LEFT +, and its negative
terminal to RIGHT -.
FULL RANGE
MONO LINE INPUT
VIA Y-ADAPTER
FROM MONO SOURCE
XXV JUNO 2 CHANNEL AMPLIFIER APPLICATIONS
PARAMETRIC EQ
BALANCED
PHASE
CUT/BOOST
LEFT
INPUT
LEVEL
LEFT
RIGHT
0dB
BANDWIDTH
FREQ
9V
0.2V
0
180
0
180
-10 +10dB
40 400Hz
X1 X10
MO ST
FULL RANGE
RIGHT
OUTPUT / INPUT
15
150Hz
40 400Hz
LP/BP
LP/BP HP
HFR-G1
SUBSONIC
FREQ
CROSSOVER
REMOTE
-6dB
XXVR-1
DIAGNOSTICS
GREEN: POWER
AMBER: THERMAL
-20dB
0dB
RED: SHORT
BASS REMOTE
PARAMETRIC EQ
BALANCED
PHASE
CUT/BOOST
LEFT
INPUT
LEVEL
LEFT
RIGHT
0dB
BANDWIDTH
FREQ
9V
0.2V
0
180
0
180
-10 +10dB
40 400Hz
X1 X10
MO ST
FULL RANGE
RIGHT
OUTPUT / INPUT
15
150Hz
40 400Hz
LP/BP
LP/BP HP
HFR-G1
SUBSONIC
FREQ
CROSSOVER
REMOTE
-6dB
DIAGNOSTICS
GREEN: POWER
AMBER: THERMAL
-20dB
0dB
RED: SHORT
BASS REMOTE
4. Line Level:
Refer to the section "Setting up systems after installation for best performance"
5. Bass Remote Module:
Plug in the Bass Remote Module to the amplifier "REMOTE" jack.
NOTE: Minimum final loudspeaker impedances:
4 & 2 Ohms stereo, 4 Ohms mono
Caution: This amplifier is not capable of 1 Ohms stereo or 2 Ohms bridged.
FUSE
RED - CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
SPEAKER OUTPUT
BRIDGED
+
L-CH
-
+
R-CH
-
X1 X10
DIAGNOSTICS
RED - SHORT CIRCUIT
AMBER - THERMAL
CLIP
FULL RANGE
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
SPEAKERS
Switch setting checklist:
The AMPLIFIER X-OVER switch must be in the FULL position.
Crossover frequency control setting checklist:
N/A for full range operation.
TIP:
If you are using the mono sub bass output of an active crossover, there is
nothing wrong with switching in the low pass filter in these amplifiers for a
steeper low pass roll-off.
Caution: This amplifier is not capable of 1 Ohms stereo or 2 Ohms bridged.
FUSE
RED - CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
SPEAKER OUTPUT
BRIDGED
+
-
+
-
L-CH
R-CH
X1 X10
DIAGNOSTICS
RED - SHORT CIRCUIT
AMBER - THERMAL
XXVR-1
CLIP
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
FULL RANGE
MONO SPEAKER
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12v VIA FUSE
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12v VIA FUSE
5