Autonics TZN4L Посібник - Сторінка 7
Переглянути онлайн або завантажити pdf Посібник для Контролер Autonics TZN4L. Autonics TZN4L 17 сторінок. Dual pid control temperature controller
Також для Autonics TZN4L: Інструкція з експлуатації (2 сторінок), Посібник (16 сторінок), Посібник (17 сторінок)
Друкувати сторінку
TZN/TZ Series
Flow chart for parameter 1 group
Run mode
If press
3sec.
MD
SV2
SU-2
(Setting value 2)
MD
AL1
AL1
setting value
MD
AL2
AL2
setting value
MD
Loop break
LBA
alarm
MD
Alarm
AHYS
hysteresis
MD
Proportional
P
band
MD
I
Integral time
MD
D
Derivative time
MD
T
Control time
MD
HYS
Hysteresis
MD
Input
IN-B
correction
MD
REST
Manual reset
MD
RAMP rising
RAPU
RAMP-up time
MD
RAMP falling
RAPD
RAMP-down time
MD
LOC
Lock
MD
※ Press
( ) key and the right digit of SV display part flashes. Press
Press
( ),
( ) keys to change SV and press
※ After completing setting at each parameter, press
※ If no key touched for 60sec., it will return to RUN mode automatically.
※
AL1 , AL2 , LBA , I , D , T , HYS , REST , RAPU , RAPD
This parameter [
Factory defaults(Parameter 1 group)
Parameter
Factory default
SU-2
0
AL1
10
AL2
10
LBA
600
H-78
key for 3sec., it will go to parameter 1 group.
MD
Set alarm temperature in SV2.
0
Set range: Within the rated using range of each sensor.
Set alarm temperature in EV-1.
10
Set range: Within the rated using range of each sensor.
Set alarm temperature in EV-2.
10
Set range: Within the rated using range of each sensor.
Set monitoring time of loop break alarm.
999
Set range: 0 to 999 sec.
Set interval between ON and OFF for alarm output.
2
Set range: 1 to 100℃ (0.1 to 100.0℃)
※ It is only displayed for temperature alarm output.
Set proportional band. / Set range: 0.0 to 100.0%.
#0
※ If setting value P as 0.0, it will be ON/OFF control.
Set integral time. / Set range: 0 to 3600 sec.
0
※ If setting value I as 0 sec., this function will be OFF.
※ It is not displayed when P is 0.0. (ON/OFF control)
Set derivative time. / Set range: 0 to 3600 sec.
0
※ If setting value D as 0 sec., this function will be OFF.
※ It is not displayed when P is 0.0. (ON/OFF control)
Set control period cycle. / Set range: 1 to 120 sec.
20
※ In case of SSR output, this value should be small.(Ex: 2sec.)
※ It is not displayed when P is 0.0. (ON/OFF control)
Set hysteresis. / Set range: 1 to 100℃ (0.1 to 100.0℃)
2
※ It is only displayed for ON/OFF control.
Correct the error in input sensor.
0
Set range: -49 to 50℃ (-50.0 to 50.0℃)
Set manual reset value. / Set range: 0.0 to 100.0%
)0
※ It is only displayed for P control.
Set ramp rising-time. / Set range: 1 to 99 min.
10
※ It displayed only when selecting Ramp function in setting 2 group.
Set ramp falling-time. / Set range: 1 to 99 min.
10
※ It is displayed when selecting Ramp function at parameter 2 group.
OFF
Cancel the lock function for OFF.
ON
This function is for locking the setting value.(available to operate
Select ON1, changing setting value in the parameter 1 group and
ON1
panel cannot be changed.
key to complete the set. Press
MD
key for 3 sec. and it returns to RUN mode.
MD
Parameter
Factory default
AHYS
P
#0
I
D
( ) or
( ) key and move to the desired digit.
MD
] might not be displayed depending on other parameter settings.
Parameter
Factory default
2
T
HYS
0
IN-B
0
REST
Key)
AT
key in the front
AT
key again and it moves to next parameter.
Parameter
20
RAPU
2
RAPD
0
LOC
)0
Factory default
10
10
OFF