Hifonics Zeus ZRX600.4 Посібник користувача - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник користувача для Автомобільний підсилювач Hifonics Zeus ZRX600.4. Hifonics Zeus ZRX600.4 14 сторінок. Zeus zrx series
Також для Hifonics Zeus ZRX600.4: Посібник користувача (14 сторінок)

Друкувати сторінку
Hifonics Zeus ZRX600.4 Посібник користувача

AMPLIFIER FEATURE DESCRIPTIONS

ZEUS ZRX AMPLIFIERS:
Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except
the mono amps which are capable of 4, 2 and 1-Ohm loads.
The input sensitivities for rated output powers are variable from 0.2V to 6V.
All crossovers are fully variable in their respective ranges.
Crossover filters are 12dB/Octave.
A POWER LED indicates the powered up and turned on condition.
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
and amplifier DC faults indicated by the red "PROTECT" LED.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30Hz to 250Hz.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 12dB.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a Mode switch. Switch to 2 channel if you only have 1 set of
RCA's in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 3 channel if you
are running stereo on ch 1&2 and mono on ch 3&4. Select 4 channel if you are providing RCA's to
channels 1/2 and 3/4.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting
simplifying daisy chaining of amplifiers.
-HPF: Selects the built in HIGH PASS filter, variable from 60 Hz to 13kHz.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS , variable from 30 Hz to 250Hz.
BASS EQ: Fixed 45Hz bass boost variable from 0dB to 12dB.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER
setting simplifying daisy chaining of amplifiers.
-SUBSONIC: Allows you to adjust the crossover filter from 15Hz to 35Hz.
-LOW PASS: Allows you to adjust the LOW PASS crossover filter from 30Hz to 250Hz.
LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.
BASS EQ: The Bass EQ is adjustable from 0db to 10dB.
REMOTE: This is the input jack for the remote Level control.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4
and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2
and 1-Ohm.
ZRX500.2 / ZRX1200.2 2-CHANNEL AMPLIFIERS
OUTPUT
INPUT
LEVEL
L
L
6V
0.2V
0dB 12dB
R
R
Note that the LOW PASS signal is MONO.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
ZRX600.4 / ZRX1000.4 / ZRX2000.4 4-CHANNEL AMPLIFIERS
CH 3 / 4
CH 1 / 2
LEVEL
R
R
6V
0.2V
LEVEL
L
L
6V
0.2V
Note that the LOW PASS signal is MONO.
-In the LPF position, the HIGH PASS filter acts as a
subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz,
BASS EQ is also switched in.
ZRX1000.1D / ZRX1500.1D / ZRX2000.1D / ZRX3000.1D 1-CHANNEL AMPLIFIERS
OUTPUT
INPUT
LEVEL
L
L
6V
0.2V
R
R
BASS EQ
X-OVER
HPF
LPF
MODE
FULL
HPF
MONO
STEREO
LPF
60HZ 13KHZ 30HZ 250HZ
CH 3 / 4
LINE OUT
BASS EQ
X-OVER
HPF
LPF
POWER
PROTECT
FULL
HPF
0dB 12dB
LPF
60HZ 13KHZ 30HZ 250HZ
BASS EQ
X-OVER
HPF
LPF
MODE
FULL
HPF
2
3
4
LPF
0dB 12dB
60HZ 13KHZ 30HZ 250HZ
CH 1 / 2
BASS EQ
REMOTE SUBSONIC
LOW PASS
POWER
PROTECT
0dB 10dB
15HZ 35HZ 30HZ 250HZ
POWER
PROTECT
2