Galaxy G9000S Інструкція з монтажу Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Сантехнічний виріб Galaxy G9000S. Galaxy G9000S 6 сторінок. Instantaneous electric shower

Друкувати сторінку

This appliance is not intended for use

by persons (Including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance.

SECTION

GENERAL LAYOUT OF A

SHOWER INSTALLATION

A TYPICAL INSTANTANEOUS ELECTRIC SHOWER INSTALLATION

Plan your own installation carefully. Check

on the nearest and most readily accessible

rising mains water supply, this may be

beneath the bath or in the loft, where it

feeds the cold water storage tank. Use

only the cold rising water main supply.

Do not connect the shower unit to the

down service from the tank.

Avoid connecting the shower unit, if

possible, were it will be affected by water

drawn off by other appliances, e.g. From

the mains feed to the W.C., This may

cause a drop in pressure too low for the

shower unit to work correctly.

An isolating valve must be fitted into the

water supply for servicing purposes.

SECTION

INSTALLATION

Position your shower unit on the wall away

from the direct spray of the shower and at

about the same height as the shower head

position.

The shower unit should be positioned so

that the shower head cannot be immersed

in the bath or shower tray when hanging

down.

Mains cold water supply

(either top, bottom or rear entry)

Remove the two screws securing the

shower unit cover and remove the cover

complete with the control knobs.

Place the shower unit on the wall and mark

the location of the fixing screws through the

back plate.

Carefully drill the holes as marked using a

sharpe 5.5mm masonry drill.

Fix the shower unit to the wall using the

plugs and screws provided, do not fully

tighten at this stage.

IMPORTANT

To comply with National Water Council

bylaws a double check valve must be

fitted with all flexible shower accessories

where it is possible that the shower head

may come into contact with used water

i.e. In the bath or shower tray.

SECTION

PLUMBING CONNECTION

Plumbing the shower unit must precede

wiring.

Turn off the water supply at the isolating

stop tap.

The back plate is fitted with removable

inserts for Top (falling) and Bottom

(rising) inlet mains water pipework to

the shower unit. Note! There is also a

Back inlet option if preferred.

We have incorporated into the bottom

right-hand side of the back plate an easy

removable trim section, to allow easy

access when connecting the water supply.

(Please Note! Remember to replace this

trim section before refitting the cover).

Connect the mains water supply to the

inlet of the shower unit using a 15mm

copper or stainless pipe with a 15mm

compression elbow or 15mmm push-fit

elbow. Do not use excessive force

when making the connection to the unit.

IMPORTANT

Before turning on the water supply to the

shower unit the water supply pipe should

be flushed out to remove debris. This can

be achieved by connecting the flexible

hose to the 15mm compression elbow and

turning on the mains water supply long

enough to clear the debris.

After flushing the pipework ensure that the

shower unit is positioned squarely on the

all and tighten the screws. Tighten all

plumbing connections and check the

pipework for leaks.

SECTION

ELECTRICAL CONNECTION

Warning! This appliance must be earthed

ELECTRICAL SPECIFICATIONS

Nominal Power

rating at 240v

rating at 230v

7.5kW -(32A MCB rating)

6.9kW -(32A MCB rating)

8.5kW -(40A MCB rating)

7.8kW -(40A MCB rating)

9.5kW -(40A MCB rating)

8.7kW -(40A MCB rating)

10.5kW -(45A MCB rating)

9.6kW -(45A MCB rating)

The shower unit must be permanently

connected to the electricity supply, direct

from the consumer unit via a double pole

linked switch with a minimum contact gap

of 3mm. The switch must be readily

accessible and clearly identifiable and out

of reach of a person using a fixed bath or

shower tray, unless the switch is cord

operated. The wiring must be connected

to the switch without the use of a plug or

socket outlet.

The cable size required is determined by

the kW rating of the shower and the

distance between the shower and the

consumer unit. The table below will help

you choose the correct cable for your

installation, but it will depend upon the

precise circumstances of the installation. If

you are in any doubt consult an electrician.

NOMINAL

MIN RATING OF

FUSE

MAX CABLE

RATING

AT 240v

ISOLATING

RATING

SWITCH

6mm

7.0

29.10amps

30 amps

29m

7.5

31.25amps

40 amps

27m

8.0

33.33amps

40 amps

25m

8.5

35.41amps

40 amps

23m

9.5

39.58amps

40 amps

21m

10.5

43.75amps

45 amps

18m

The incoming cable should be hidden.

RUN

10mm

48m

44m

42m

38m

32m

30m