DynaQuip Controls WaterCop Посібник користувача - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник користувача для Система водопостачання DynaQuip Controls WaterCop. DynaQuip Controls WaterCop 8 сторінок. Automatic water shut-off systems

Друкувати сторінку

Note: If major repairs are needed to correct the

plumbing system, it is recommended that the manual

shut-off valve upstream of the WaterCop

closed during the repairs. Close the main water shut-

off valve and unplug the WaterCop

repairs on the plumbing system.

Note:

In case of a power failure, the WaterCop

cannot operate. If the power is out, you will need to use

the manual shut-off valve to turn the water off in case

of an emergency.

When power is restored, the

WaterCop

will remain in its last known position indi-

cated by the red or green lights on the face of the unit.

WaterCop

Specifications

Max. working pressure ...125 PSIG

Ambient temperature .....35° to 105° F

Enclosure .......................Polycarbonate

Voltage ...........................115, 1 Phase, 60 Hz

Current ...........................2.5 Amps

Power Input:

Standby ..........................1.375 W

Holding (2.5 sec) ............75 W

Power Cord ....................8 ft. Heavy-Duty Grounded

Valve ..............................Full-Port, Brass, NPT

Valve Seals ....................RTFE

Flow Data

Valve Size Cv = Gpm flow @ 1 PSI pressure drop

1/2" NPT

3/4" NPT

1" NPT

For cold water applications.

FCC Information

This equipment has been tested and found to comply

within limits of a class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation.

to check all areas where

you have placed a sensor

to determine what plumb-

ing product caused the

system to activate. The

valve will remain closed

until the unit is manually

reset on the WaterCop

panel. After the plumbing

problem is fixed, reset the

WaterCop

by pressing

"open valve" (green circle)

the

face

the

WaterCop

Valve will

open and green indicator

will be lit. See illustration to

the lower left.

also be

before doing

This

The flood sensors only transmit a radio signal during

testing and when contact is made between the probes

as when water is detected. This signal is of a 2-second

duration and is repeated approximately every 6

seconds while activated. This 2 second signal should

be the only time potential interference could be

detected. If you suspect the unit is interfering with your

radio and/or television reception on a prolonged basis,

remove batteries from all transmitters to determine if

this unit is causing the interference. If so, please

consult your dealer.

LIMITED WARRANTY

DynaQuip Controls Corporation warrants the electrical

components of the WaterCop

defects in material and workmanship under normal use

and if properly installed for a period of three years from

the date of purchase. If found to be defective as men-

tioned above, it will be replaced or repaired if returned

prepaid along with proof of date of purchase. This shall

constitute the sole remedy of the purchaser and the

sole liability of DynaQuip Controls Corporation. To the

extent permitted by law, the foregoing is exclusive and

in lieu of all other warranties or representations

whether expressed or implied, including any implied

warranty of merchantability or fitness. In no event shall

DynaQuip Controls Corporation be liable for special or

consequential damages.

The WaterCop brass ball valve has a lifetime warran-

tee.

Additional Components available for your

WaterCop

Systems:

Single and Dual probe WaterCop

• WH100 (single probe) and WH200 (dual probe)

• Battery or AC (optional) powered

• Transmits wireless signal to valve when moisture is

detected.

• Unlimited number can be used, placed anywhere

• 6 foot sensor cord, white

Low Temperature Sensor

• FH100

• Monitor temperature of pipes prone to freezing

• Sends wireless signal to turn off water if low temperature

detected

• 5 foot cord with clip to attach to pipe

Water Control Wall Switch

• RS100

• Proactively turn water on or off from convenient location

• Lighted display to valve position (on or off)

• Requires Category 5 cabling connection to valve (see

below)

AC Power Adaptor

• For WH100, WH200, and FH100 sensors.

• Eliminates the need for AA batteries

WaterCop / Wall Switch Interconnect Cable

• CBL50 (50 feet) and CBL100 (100 feet)

• Required to connect WaterCop valve with Water Control

Wall Switch

• RJ45 molded connections for easy installation and

durability

system to be free from

Flood Sensors