Autonics BYD DDT Series Посібник з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Датчики безпеки Autonics BYD DDT Series. Autonics BYD DDT Series 5 сторінок. Photoelectric sensors with built-in timer
Друкувати сторінкуSpecifications
Model
BYD3M-TDT-□-□
Sensing type
Through-beam
Sensing distance
3 m
Sensing target
Opaque materials
Min. sensing target ≥ Ø 6 mm
Hysteresis
-
Response time
≤ 1 ms
Light source
Infrared
Sensitivity
-
adjustment
Timer function
-
Operation mode
Dark ON mode
Front
Indicator
Operation indicator (red)
Certification
ᜢ ᜨ ᜫ
Unit weight
It depends on the model.
(packaged)
Cable type
≈ 80 g (≈ 105 g)
Cable connector
≈ 40 g (≈ 65 g)
type
01) Non-glossy white paper 50 × 50 mm
02) When the timer adjuster is set to min (0.1 sec).
Power supply
12-24 VDCᜡ ±10 % (ripple P-P: ≤ 10 %)
Current
It depends on the sensing type
consumption
Through-beam
Emitter: ≤ 30 mA, receiver: ≤ 30 mA
Reflective
≤ 35 mA
Through-beam type
: NPN open collector output / PNP open collector output model
Control output
Diffuse reflective, convergent reflective type
: NPN open collector output
Load voltage
≤ 26.4 VDCᜡ
Through-beam type : ≤ 100 mA
Load current
Diffuse reflective, convergent reflective type : ≤ 50 mA
Residual voltage
NPN: ≤ 1 VDCᜡ, PNP: ≤ 2.5 VDCᜡ
Reverse power protection circuit,
Protection circuit
output short overcurrent protection circuit
Insulation
≥ 20 MΩ (500 VDCᜡ megger)
resistance
±240 VDCᜡ the square wave noise (pulse width: 1 ㎲) by the noise
Noise immunity
simulator
Between the charging part and the case: 1,000 VACᜠ 50/60 Hz for 1 min
Dielectric strength
1.5 mm double amplitude at frequency of 10 to 55 Hz
Vibration
in each X, Y, Z direction for 2 hours
Shock
500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times
Ambient
illuminance
Sunlight: ≤ 11,000 lx, incandescent lamp: ≤ 3,000 lx
(receiver)
Ambient
-20 to 65 ℃, storage: -25 to 70 ℃ (no freezing or condensation)
temperature
Ambient humidity
35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
Through-beam, convergent reflective type (front operation indicator
Protection rating
model): IP64 (IEC standard), Others: IP50 (IEC standard)
Connection
Cable type / Connector cable type model
Cable spec.
Ø 3.5 mm, 3-wire (Emitter: 2-wire), 2 m
Wire spec.
AWG26 (0.52 mm, 20-core), insulator outer diameter: Ø 1 mm
Connector spec.
M12 4-pin plug type
Case: PC, sensing part: PC, bracket: SPCC, bolt: SCM, nut: SCM,
Material
sleeve: Brass, Ni-plate
BYD100-DDT-□
BYD□-DDT-□-□
Diffuse reflective
Convergent reflective
10 to 30 mm
10 to 50 mm
100 mm
01)
±10%
±10%
01)
Opaque materials,
Opaque materials,
translucent materials
translucent materials
-
-
≤ 25 % of sensing
≤ 10 % of sensing distance
distance
Operation: ≤ 3 ms
Operation: ≤ 3 ms
Return: ≤ 100 ms
Return: ≤ 100 ms
Infrared
Infrared
YES (Adjuster)
-
OFF delay mode
-
: 0.1 to 2 sec (Adjuster)
Light ON mode
Light ON mode
Front / Upper operation
Front
indicator model
ᜢ ᜨ ᜫ
ᜢ ᜨ ᜫ
≈ 38 g (≈ 75 g)
≈ 38 g (≈ 75 g)
≈ 18 g (≈ 55 g)
≈ 18 g (≈ 55 g)
Sold Separately: Bracket B
• Unit: mm, For the detailed drawings, follow the Autonics website.
8
2-R1.6
01)
2-R1.6
21.5
8.8
45
25
20
C4
02)
Sold Separately: Slit for Through-beam Type
■ BYD3M-ST (sticker)
• Unit: mm
9.8
A
Applied condition
A
Emitter
Ø 1.0 mm
Ø 1.5 mm
Ø 2.0 mm
Ø 2.5 mm
4-R2.2
4-R0.5
2-R2.2
• Attach this slit at both an emitter and a receiver.
( packaged unit: 2 pieces of each different Ø,
total 8 pieces)
• Gently wipe the dirt on the lens of the sensor
before using it.
• After attaching the slit, remove the front protection
film.
Min. sensing
target
Receiver
≥ Ø 0.8 mm
Opaque materials
≥ Ø 1.5 mm
Opaque materials
○
○
≥ Ø 2.0 mm
Opaque materials
≥ Ø 2.5 mm
Opaque materials
Max. sensing
distance
500 mm
700 mm
1,200 mm
2,300 mm