High End Systems ROAD HOG Посібники з швидкого старту - Сторінка 2

Переглянути онлайн або завантажити pdf Посібники з швидкого старту для Музичний мікшер High End Systems ROAD HOG. High End Systems ROAD HOG 2 сторінки.

Друкувати сторінку

System Restore

The Road Hog system restore routine

The partial recovery process will reinstall the XPe

allows reinstallation of the software from

image and the Wholehog software without erasing

a location on the internal hard drive or

your show files.

from external USB drives.

5. The console immediately begins drive restoration. The

process may take anywhere from 10-15 minutes, and

System Restore from Internal Drive

will automatically reboot your console when finished.

The Road Hog console includes a system restore routine

Do not touch any keys or attempt to interrupt the

that can restore the original software and XPe image on the

restore process. If the process is interrupted for any

console. A protected partition on the hard drive stores the files

reason, simply reboot and return to Step 1 to ensure

needed to create a clean restore of the Road Hog console

the Road Hog console is completely restored.

software. Newer versions of software may be available at

6. Once the system is restored and rebooted, remove the

www.flyingpig.com. To restore your system files from the hard

System Restore USB drive and store in a safe place.

drive, you'll need a USB Keyboard.

Restoring Touchscreen Configuration

Using the Road Hog System Restore Image

after a Full Restore

1. Connect a keyboard to the console.

Following the completion of a full system restore process,

2. As the system boots up, press any key on the keyboard

use the following steps to calibrate the touchscreens.

when the boot manager screen is displayed. Note: This

1. Navigate to the Displays tab in the Control Panel.

screen is displayed for only one second during the

2. Press the Calibrate Touchscreens button and follow

boot process.

the on-screen instructions.

3. Select Road Hog System Restore from the boot manager

3. Press Setup->Quit then select Shutdown. Once

screen and press Enter on the keyboard. Note: Selecting

shutdown, reboot the console to confirm the screens

Road Hog Console will boot the console normally.

are calibrated.

4. A recovery screen will prompt you to select a Partial

recovery or Exit. Note: The partial recovery process

Creating a Bootable USB Flash Drive

will reinstall the XPe image and the Wholehog

The Road Hog console system restore routine also contains

software without erasing your show files.

a utility to create bootable USB flash drives with or

5. The console immediately begins drive restoration. The

without a restore image.

process may take anywhere from 10-15 minutes, and

CAUTION: This process will remove ALL files from the

will automatically reboot your console when finished.

USB flash drive.

Do not touch any keys or attempt to interrupt the restore

To create a bootable USB flash drive, you'll need: a

process. If the process is interrupted for any reason, simply

Road Hog System flash drive or other bootable capable

reboot and return to Step 1 to ensure the

flash drive greater than 500 MB and a USB Keyboard.

Road Hog console is completely restored.

Using the Road Hog System Restore Utility

System Restore from USB Drive

1. Connect a keyboard and make sure the bootable USB

The Road Hog console system restore routine can restore the

flash drive is not connected to the console.

original software or upgrade the XPe image from external USB

2. As the system boots up, press any key on the keyboard

drives (Flash, CD, ZIP, etc). Newer versions of software may

when the boot manager screen is displayed. Note: This

be available at www.flyingpig.com. To restore your system

screen is displayed only for one second during the

files, you'll need a USB keyboard and a Road Hog System

boot process.

Restore image on a USB drive (flash, CD, or Zip drive) Note:

3. Select Road Hog System Restore from the boot manager

The image must be an ISO image properly extracted to a

CD or bootable flash drive. Instructions on creating a

Road Hog Console will boot the console normally.

bootable flash drive follow.

4. The recovery screen will be displayed; at the bottom of

Using the Road Hog System Restore Image

the screen select the button labeled Create bootable

1. Connect a keyboard and your USB drive containing the

flash drive.

System restore image.

5. Insert the USB flash drive and select it from the drop down

2. As the system boots up, press F8 on the keyboard to

list to make bootable.

display the boot device selection screen.

6. To place the current XPe image from this Road Hog

3. Select the USB device that contains the system restore

console on the flash drive, select the check box

image from the list.

labeled Add restore files to the flash drive.

7. Press Select to create the USB bootable flash drive image.

4. A recovery screen will prompt you to select a Full or Partial

recovery. A full recovery will erase the show files on the

8. When complete, select Exit from the restore screen to

hard drive and a partial will not.

boot the console.

CAUTION: The Full recovery process will remove

9. Once the USB flash drive is made bootable, you can

ALL data from the Road Hog hard drive including

Pig website containing the latest Road Hog image.

show files.

screen and press Enter on the keyboard. Note: Selecting

use a computer to extract an ISO image from the Flying

Monitor Controls

On Screen Display (OSD) menu control buttons are located on the top of the console above each monitor

screen. Use these buttons to access the OSD menu system's monitor controls.

AUTO/SEL DOWN

Displays and exits the OSD Screen

Navigates the OSD options clockwise and

increases value of a selected OSD control option

Navigates the OSD options counterclockwise and

decreases value of a selected OSD control option

Auto centers screen when OSD screen is not displayed.

When the OSD screen displayed, use SEL to select an OSD

control option and then select the option value you choose

To adjust an OSD option:

1. Press the MENU button to display the OSD Menu.

2. Press the UP button or the DOWN button to navigate to a OSD control option.

3. When the function you want to change is displayed, press the SELECT button.

4. To adjust the Value of the function:

5. Press the UP button increases the value of the selected OSD control option.

6. Press the DOWN button decreases the value of the selected OSD control option.

7. After adjusting the values, press the SELECT button again and the monitor automatically saves

the changes.

OSD Control Option Descriptions

Contrast

adjusts the contrast or the values of color gain (RED, GREEN or BLUE)

Brightness

adjusts the background Luminance of the LCD panel

V-Position

adjusts the display window vertically on the screen

H-Position

adjusts the display window horizontally on the screen

Recall Defaults

resets the factory OSD default settings.

RGB

selects Color Temperature and sets R, G, B gain.

Volume

(not used)

Sharpness

adjusts the color intensity and tint

Phase

(not used)

Clock

(not used)

OSD H-Position

positions the OSD menu screen horizontally in the monitor display

OSD V-Position

positions the OSD menu screen vertically in the monitor display

OSD Timeout

adjusts the amount of time in which the OSD will disappear

Auto Adjust

automatically refreshes the screen and exits the OSD

Language

chooses between English, French, German, Spanish and Japanese for OSD

Info

displays the current monitor resolution and refresh rate

Note: The OSD screen will disappear if no input activities are detected for 45 seconds.

Returning an Item Under Warranty for Repair: It is necessary to obtain a Return

Material Authorization (RMA) number from your dealer or point of purchase BEFORE

any units are returned for repair. The manufacturer will make the final determination

document are subject to change without notice. Certain specifications may be the

as to whether or not the unit is covered by warranty.

result of future software releases. High End Systems, Inc. assumes no responsibility

or liability for any errors or inaccuracies that may appear in this manual.

Any Product unit or parts returned to High End Systems must be packaged in a

suitable manner to ensure the protection of such Product unit or parts, and such

Trademarks

package shall be clearly and prominently marked to indicate that the package contains

High End Systems, the Flying Pig Systems logo, the WHOLEHOG, Road Hog and

returned Product units or parts and with an RMA number. Accompany all returned

WHOLEHOG III logos are registered trademarks of High End Systems, Inc.,or High End

Product units or parts with a written explanation of the alleged problem or

Systems, Europe Ltd. Flying Pig Systems, Effects Engine, and Hog are registered

malfunction. Ship returned Product units or parts to: High End Systems, 2105 Gracy

trademarks of Flying Pig Systems. Road Hog is a trademark of High End Systems, Inc.

Farms Lane, Austin, Texas 78758.

Windows is a registered trademark of Microsoft corporation. IntelliTouch,

Note: Freight Damage Claims are invalid for products shipped in non-factory boxes and

SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo

packing materials.

TouchSystems, Inc.

Freight: All shipping will be paid by the purchaser. Under no circumstances will freight

All other brand names and product names used in this book are trademarks, registered

collect shipmentsbe accepted.

trademarks, or trade names of their respective holders.

REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE

Warranty Information

EXCLUSIVE REMEDY OF THE CONSUMER. HIGH END SYSTEMS, INC. MAKES NO

Limited Warranty: Unless otherwise stated, your product is covered by a one year

WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, AND

parts and labor limited warranty. It is the owner's responsibility to furnish receipts or

HIGH END SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR

invoices for verification of purchase, date, and dealer or distributor. If purchase date

FITNESS FOR A PARTICULAR PURPOSE. HIGH END SHALL NOT BE LIABLE FOR ANY

cannot be provided, date of manufacture will be used to determine warranty period.

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS,

SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY

Troubleshooting

The table below describes basic troubleshooting for the Road Hog console hardware. For software

troubleshooting, refer to the Wholehog User Manual or on-line help.

If a problem persists after you try the suggestions listed in the following table, contact High End Systems

Support at 800.890.8989 or [email protected].

Problem

Suggestion(s)

Check that the AC power switch at the back of the console is ON. Press the

The console does not boot

power button to boot the console.

Check that fixtures are properly patched

Turn the AC power switch at the back of the console to OFF, wait 10 seconds and turn

No DMX output

it back on.

Look for DMX indicators on fixtures or with a DMX tester.

Check that timecode is properly enabled and that the USB LTC widget is properly

connected.

Turn the AC power switch at the back of the console to OFF, wait 10 seconds and turn

No Timecode Input

it back on.

Confirm timecode source is valid with a timecode tester.

Confirm the Grand Master fader (usually master #1) is up.

Confirm the master for the cuelist is up.

No intensity control on

If fixtures are in the programmer or editor, turn off the Blind function.

fixtures

Check to ensure intensity values are not parked.

Press Pig + Open + Backspace to open the Launched Processes window and kill

The software has frozen or

processes that are not responding by right clicking on them and selecting Kill. Then

quit unexpectedly

restart the process by right clicking and selecting Restart.

The process window will not

Press and hold the

power button located on the top of the console for 10 seconds

open after the software has

to reboot the console.

frozen or quit unexpectedly

Cleaning the Road Hog Console and Touchscreens

To clean the console and touchscreens, use only a soft cloth damped with water. Glass cleaner or other

solvents will dull the finish of the console. Do not use alcohol (methyl, ethyl or isopropyl) or any strong

solvent. Do not use thinner or benzene, abrasive cleaners or compressed air. Do not wipe the screens with a

cloth or sponge that could scratch the surface.

Upgrading the Wholehog Application

The Wholehog control software is being upgraded continually and it is likely that

there is a newer version available. You can find the latest versions at the Flying Pig

Systems website (

http://www.flyingpig.com/support/hog3/downloads/index.shtml

Refer to Section 37 of the Wholehog user manual for a description of how to

upgrade the Wholehog application.

PRODUCT DEFECTS OR THE PARTIAL OR TOTAL FAILURE OF ANY PRODUCT

Produktmodifikationswarnung

REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT

Design und Herstellung von High End Systems entsprechen den Anforderungen der

(INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, AND WHETHER OR

U.S. Amerikanischen

NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.

undinternationalen Sicherheitsvorschriften. Abänderungendieses Produktes können

Warranty is void if the product is misused, damaged, modified in any way, or for

dessen Sicherheit beeinträchtigen und unter Umständen gegen die diesbezüglichen

unauthorized repairs or parts. This warranty gives you specific legal rights, and you

Sicherheitsnormen verstoßen.

may also have other rights specific to your locality.

Avvertenza Sulla Modifica Del Prodotto

I prodotti di High End Systems sono stati progettati e fabbricati per soddisfare i

Product Modification Warning

requisiti delle normative di sicurezza statunitensi ed internazionali. Qualsiasi modifica

High End Systems products are designed and manufactured to meet the requirements

al prodotto potrebbe pregiudicare la sicurezza e rendere il prodotto non conforme agli

of United States and International safety regulations. Modifications to the product

standard di sicurezza pertinenti.

could affect safety and render the product non-compliant to relevant safety

standards.

Advertencia De Modificación Del Producto

Mise En Garde Contre La Modification Du Produit

Los productos de High End Systems están diseñados y fabricados para cumplir los

Les produits High End Systems sont conçus et fabriqués conformément aux exigences

requisitos de las reglamentaciones de seguridad de los Estados Unidos e

des règlements internationaux de sécurité. Toute modification du produit peut

internacionales. Las modificaciones al producto podrían afectar la seguridad y dejar al

entraîner sa non conformité aux normes de sécurité en vigueur.

producto fuera de conformidad con las normas de seguridad relevantes.

H i ghEnd Syst em s

)