High Resolution Technologies Security Camera Посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник користувача для Камера спостереження High Resolution Technologies Security Camera. High Resolution Technologies Security Camera 2 сторінки. High resolution technologies security camera user manual
Друкувати сторінкуInstalling a Direct (DC) Drive Lens
1. If using a C-mount lens, fit the C-mount adaptor ring
and slide the back focus adjsutment fully to the left with
the lens facing towards you (see Setting the Focus).
2. Fit the lens to the camera and connect it to the DC lens
socket, as defined by the pin assignments in Figure 1.
CAUTION: The maximum load for this type of lens
must not exceed 25mA.
3. Access the menu and select LENS > BF. (See LENS -
BF Function)
4. If a focus ring is fitted on the lens, set it to infinity (∞)
and then adjust the back focus.
5. Exit the BF menu to return to normal operation.
Installing a Video Drive Lens
1. If using a C-mount lens, fit the C-mount adaptor ring
and slide the back focus adjsutment fully to the left with
the lens facing towards you (see Setting the Focus).
2. Fit the lens to the camera and connect it to the Video
Lens connector, as defined by the pin assignments in
Figure 2.
CAUTION: The maximum load for this type of lens
must not exceed 50mA.
3. Access the menu and select LENS > BF. (See LENS -
BF Function)
4. If a focus ring is fitted on the lens, set it to infinity (∞)
and then adjust the back focus.
5. Exit the BF menu to return to normal operation.
Setting Video Drive Lens Level
1. Access the menu and select:
DAY MODE > SETTING > AGC.
2. Note the current value. Then set to "1" and exit the
menu.
3. Adjust the lens level potentiometer for the correct
exposure. (This can be achieved manually, or by using
an oscilloscope or level meter to set the output of the
camera to 1V peak-peak).
4. Return the AGC to the previously noted setting.
DC LENS
Pin Number
Pin 1
4
1
Pin 2
3
2
Pin 3
Pin 4
Figure 1
Camera OSD Menu
DAY/NIGHT
DAY MODE
NIGHT MODE
LENS
BLC
WHITE BALANCE
SYNC
MIRROR
TITLE
PRIVACY ZONE
RS485
Menu Navigation
Open the panel on the side of the camera to access the
Navigation Control Pad and Set Key.
Press and hold the SET Key on the side of the camera to
access the main menu
Use the Up/Down buttons on the Contol Key to select the
desired menu option. If a sub menu is available, this is
indicated by
Pressing the SET key will open the sub-menu.
Values are changed using the Left/Right buttons.
Remember to select SAVE before exiting the menu or
else changes will not be implemented when the camera
is next powered up.
LENS - BF Function
This function provides the installer with a simplified method
of adjustment of optical back focus. When used with an
auto iris lens, this function will automatically fully open the
IRIS of the lens and swtich the camera to AES (auto
electronics shutter) mode whilst the BF option is selected.
In the case of a manual lens, this function will automatically
switch to AES.
Move the cursor to LENS with the Control Key, select BF
and press SET key. Whilst in BF mode " Press SET for
return" is displayed on the monitor.
Adjust the optical back focus for optimum focus then press
SET key to return to the top menu. ( Please refer to section
"Setting the Focus" ).
DC Drive
Damp-
Damp +
Drive -
Drive +
D/N LEVEL
AUTO
BURST
NIGHT
DELAY TIME
DAY
BURST
SHUTTER SPEED
SETTING
BRIGHT
APERTURE
AGC
CHROMA
GAMMA CORR
BF
LEVEL
LEVEL
OFF
ZONE 4
ZONE 1
ZONE 5
ZONE 2
ZONE 3
ZONE 6
LEVEL
ATW
ATW-EX
MWB
WB PUSH
R GAIN LEVEL
B GAIN LEVEL
INTERNAL
WB PUSH
LINE LOCK
V-PHASE
OFF
ON
TEXT
OFF
POSITION
ON
FLASH
ZONE 1
ZONE 3
SET ZONE
ZONE 2
ZONE 4
ADDRESS
SETTING
BAUD RATE
-
-
+
+
VIDEO LENS
Figure 2
HIGH
STANDARD
LOW
AUTO/ON
05 Sec
10 Sec
20 Sec
30 Sec
60 Sec
1/50 (1/60)
1/120(1/100)FLK
1/250
1/500
1/1K
1/2K
1/4K
1/10K
1/100K
AES
LEVEL 1-15
LEVEL 1-9
1-9
COLOR ROLLING
00-FFh
LOCK/PUSH ON
OFF/ON
0-999
9600 bps
19200 bps
Specifications
General
NTSC
Image Size
1/3 Format Interline CCD Sensor
Pixel Element
768(H) x 494(V)
Scanning Frequency
NTSC 2:1 Interlace
H:15750Hz V:59.94Hz
Operation/Storage Temperature
-10°C~50°C / -20°C~60°C
Relative Humidity
<90% Non-Condensing
Output Terminal
BNC 75Ω unbalanced
AC Supply
20~29VAC
Power Source
DC Supply
11~28VDC
Power Consumption
4.5W Max
Power Indicator
3Ø Green LED on Rear Panel
Video Drive
3pin Push Lock Terminal Block on Rear
IRIS Connector
DC Drive
4pin Connector on Rear
Lens Mount
CS Mount, Change C Mount by Adaptor
Back Focus Adjust
CS Mount 12mm +/- 1.0mm, Adjust by screw
Mounting Hole
1/4" Top and Bottom
External Dimension
73mm(W) x 63mm(H) x 122mm (L)
Functional Specification
NTSC
Exposure Control
Auto Detection for AES (Fixed Iris), DC Iris or
Video Iris Lenses.
AES
Auto Luminance Control
1/60 (1/50) ~ 1/100000 sec Max.
MES
8 Step: 1/60(1/50), 1/120(1/100), 1/500,
1/1000, 1/2000, 1/5000, 1/10000
Auto IRIS Control
Video Drive / DC Drive Separate Output
Video IRIS Output
600mV Vpp (100IRE Video Output)
DC IRIS Output
1.2V at 85Ω Impendance
White Balance
Auto White Balance/ Push White / Manual
White Balance
Auto White Balance Range
Standard Range: 2700K ~ 9700K
Extended Range: 2500K ~ 15000K
Manual White Balance Range
1 Preset; R gain and B gain Adjustable
Day & Night
Optical Low Pass Filter Removable (Auto
Detect) <Fuzzy 30 IRE ~80 IRE>
IR Lamp Trigger
External Relay Contact input for IR switching
AGC Boost
Enhanced AGC Gain to Max. 30dB
Color Killer
Fuzzy / ON / OFF
SYNC System
INT / Line Lock
Phase Adjust Range
0°C~270°C
Line Lock
Frequency Range
60Hz +/- 1Hz
Video Specification
NTSC
Normal Mode
540 TV Line
Resolution
TDN Mode
570 TV Line
Day Mode
0.6Lux @ F=1.2 (50IRE Video Output)
Minimum Illumination
Night Mode
0.1Lux @ F=1.2 (40IRE)
Video Output
1.0Vpp 75Ω BNC unbalance
95 IRE
50dB
S/N Ratio
40 IRE
38dB
Close IRIS
38dB
AGC Max Gain
30dB
AGC Default Gain
24dB
White Clip
120 IRE Max
Pedestal Level
7.5 +/- 2.5 IRE
SYNC Level
40 +/- 2 IRE
Burst Level
40 +/- 2 IRE
Aperture
15 Step, Level adjustable 0 IRE~15 IRE
(r=0.45 @ 100 IRE output)
Mirror
ON / OFF
Gamma Compensation
9 Step
Gamma Crosses Point
55 IRE ~ 65 IRE
Gamma Block Level
10 IRE ~ 15 IRE
Bright Level
15 Step
Chroma Level
9 Step
Function Control or Adjustment
NTSC
Exposure Control
Auto Detect
Color Killer
Fuzzy ON / OFF
BLC
6 Areas with adjustable levels
Auto White Balance
2700K~9700K / 2500K~15000K
AGC Gain Control
18dB~30dB Linear Adjustment
SYNC System
INT / LL Switchable
V-Phase
0°~270°
Remote Control
* RS-485, Two way communications
Address
000~999
* RS-485
For further information on the remote RS485 control contact your
local representative
PAL
752(H) x 582(V)
PAL 2:1 Interlace
H:15625Hz V:50.0Hz
PAL
50Hz +/- 1Hz
PAL
PAL