Dynasty Spas MC-MP-DY4 Коротка довідкова картка - Сторінка 2

Переглянути онлайн або завантажити pdf Коротка довідкова картка для Гідромасажна ванна Dynasty Spas MC-MP-DY4. Dynasty Spas MC-MP-DY4 2 сторінки. Spa pack

7
Step
Programming
Sequence
Step 1
Time of day
Step 2
Filter cycle start time
Step 3
Filter cycle duration
Step 4
Filter cycle frequency
Step 5
Economy mode start time
Step 6
Economy mode duration
Step 7
Storing settings in memory & returning to Normal mode
Step 1- Time of day
Setting the time:
1- Enter Programming mode by holding
Prog. key pressed down for 2 seconds.
2- The display will show the current time.
10:25
am
3- Use Up and Down arrows to change
11:43
pm
the hours.
4- Prog. key a second time to select the
minutes.
5- Use Up and Down arrows to change
setting.
Steps 2 & 3- Filter cycle start time & duration
The system automatically performs two filter cycles per day, at
12-hour intervals. During the filter cycle, Pumps 1 & 2 and the
blower will run the first minute, then Pump 3 will run for one
minute. Pump 1 will then run at low speed for a programmed
number of hours. The "Filter Cycle" icon lights up when a filter
cycle is on.
To program a filter cycle, you must enter: 1) the time you want
the cycle to start and 2) the duration of the cycle. If no filtering is
required, the duration should be set to "0". For continuous
filtering, the filter cycle duration should be set to "12:00".
Setting filter cycle start time:
1- Press Prog. key a third time.
2- The display will show FSxx, with "xx"
FS01
representing the starting hour.
3- Use Up and Down arrows to change
FS12
setting.
Setting filter cycle duration:
1- Press Prog. key a fourth time.
2- The display will show Fdxx, with "xx"
Fd00
representing the duration in hours.
3- Use Up and Down arrows to change
Fd12
setting.
Step 4- Filter cycle frequency
Setting filter cycle frequency:
1- Press Prog. key a fifth time.
2- The display will show FFxx, with "xx"
FF01
representing the frequency per day.
3- Use Up and Down arrows to change
FF04
setting.
Steps 5 & 6- Economy mode start time & duration*
Setting Economy mode start time:
1- Press Prog. key a sixth time.
2- The display will show ESxx, with "xx"
ES10
representing the starting hour.
3- Use Up and Down arrows to change
ES08
setting.
Setting Economy mode duration:
1- Press Prog. key a seventh time.
2- The display will show Edxx, with "xx"
Ed01
representing the duration in hours.
3- Use Up and Down arrows to change
Ed04
setting.
Step 7- Storing settings in memory
Press Prog. key an eighth time to store settings in the system's
non-volatile memory and to return to Normal mode.
Temperature
unit
Filter Cycle
Heater
icon
icon
Programming Mode
Economy Mode
icon
icon
Digital control pad lockout
This function allows you to prevent unauthorized parameter
setting of the unit. This feature is especially helpful when young
children have access to the keypad.
There are two modes you can choose from: Full lock or Partial
lock. Full lock means that all keypad functions are locked. Partial
lock means that the basic functions of the spa will remain accessi-
ble (pumps, blower and light), but it will be impossible to change
the temperature Set Point, to override the Economy mode or
to enter the Programming mode.
When control pad is locked, the "Lock" icon will be displayed.
Locking your digital control pad:
LocP
LocF
When control pad is locked, all automatic functions of the system
run as usual. If a key is pressed down, a "LocP" or "LocF"
message will be displayed for 1 second. To unlock the keypad,
simply press and hold Pump 1 key again for 5 seconds.
When control pad is unlocked, the "Ulock" icon will be displayed.
Economy mode
Press Econo key to switch from Normal mode to Economy
mode. To save energy, the Economy mode Set Point is 20˚F
(11˚C) below the Normal mode Set Point.
The "Economy Mode" icon lights up when Economy
mode is on.
There are 3 available Economy operating modes:
noEc:
No Economy mode
Ec 1:
Economy mode always on
Ec 2:
Economy mode on during a programmed
number of hours (see Steps 5 & 6*)
Selecting the desired Economy mode:
noEc
Ec 1
After 5 seconds, the new setting will be programmed.
Summary of control panel parameters
FSxx Filter cycle start time
Fdxx Filter cycle duration
FFxx Filter cycle frequency
ESxx Economy mode start time
Edxx Economy mode duration
LocX Control pad lockout
Up & Down
arrows
Lock
icon
1- Press and hold Pump 1 key for
5 seconds.
2- The display will show LocP, with "P"
representing Partial lock.
3- Release the key and the keypad will be
in Partial lock mode. Keep key pressed
down for 5 more seconds if you want
to be in Full lock mode. The "LocF"
message will then be displayed.
1- Press and hold Econo key for
more than 2 seconds.
2- The display will show the current
mode (noEc, Ec 1 or Ec 2).
3- Keep key pressed down until the
desired mode is displayed.
Smart
Winter
Mode
TM
9919-100494-B