Copper Creek EDA-33 Посібник з експлуатації

Переглянути онлайн або завантажити pdf Посібник з експлуатації для За замками Copper Creek EDA-33. Copper Creek EDA-33 2 сторінки. Electronic deadbolt

Друкувати сторінку

*Important information:

The preset UC and PC code are unique and different for each deadbolt.

Change the UC and PC code as soon as possible after installation to ensure security (Please refer to the following functions

Step 4.2).

Every programming operation has to be done while in unlocked mode.

If wrong UC is entered, press the

Note: UC and PC can be up to 4-10 random digits in length.

One unique PC and 2 random UC are printed on two separate stickers, One on this manual, the other on the interior

face of exterior keypad. Please keep this operation manual in a safe place for security purposes.

FUNCTIONS

1.1 Automatic-Bolt Direction

Determination (Door Handing)

1.2 To unlock

1.3 To lock

2.1 To add new user code

(up to 6 different UC )

2.2 Delete one existing user code

2.3 Delete all user codes

2.4 Automatic locking set

and cancel

2.5 Mute Mode

3.1 Program the new remote control

(up to 6 remote controls)

3.2 Delete all remote controls

4.1 Change Programming Code

4.2 Recover the preset

programming code

5.2 Create a temporary user code

(e.g. guest, neighbor, etc.)

OPERATION MANUAL FOR DIGITAL DEADBOLT

Message definitions and notes:

Button operation: The button illuminates for 5 seconds and beeps once when pressed.

Successful Programming: LED flashes green one time with one melody.

Fail Programming: LED flashes red one time with one melody.

The LED will flash red three times and sound three beeps when you fail to lock properly.

Complete all the steps of adding the UC or Remote control in the programming mode within 10 seconds.

Mute mode: All audio will be cancelled but the signals are still active. Mute does not affect audio warning when

battery is low.

In Mute mode, LED flashes green indicating the operation is successful; LED flashes red indicating the

operation is unsuccessful.

LED will flash red and beep for 5 seconds if wrong user code is entered 4 consecutive times or if 20 wrong

digits are entered consecutively, the lock will stop operating for 3 minutes after the beeping stops. (Hint:

Turning turnpiece or key to unlock will reactivate the lock.)

Lock must be in the unlocked mode before programming. If programming attempted while in locked mode,

wait 5 seconds, unlock and re-program.

10. If programming fails (while in the unlocked mode), confirm the turnpiece is vertical and the deadbolt retracts

properly.

11. Low battery warning: Replace with four alkaline batteries when LED flashes red 15 times accompanied by 15

rapid beeps.

Note

：

○

button first to clear the wrong code, and then input the correct UC.

1.1.1 Insert only three batteries first, and then press and hold

1.1.2 Release the

button When you hear 3 beeps and LED flashes green 3 times, then the lock automatically determines the "door

handing" and sets the proper direction for motor to rotate.

1.1.3 LED flashes green followed by a confirming melody.

1.2.1 Enter a valid UC, and the lock will automatically unlock.

1.2.2 The turn piece should be vertical when the lock is in the unlocked position.

1.3.1 Press the lock button to lock.

1.3.2 The turn piece should be horizontal and the bolt extended in the locked position.

Note

：

I f the operation fails, the latch bolt will extend twice automatically.

2.1.1 In the unlocked mode, input PC and press

2.1.2 Enter a new UC and then press

2.2.1 In the unlocked mode, input PC and press

2.2.2 Enter the exiting UC and then press

2.3.1 In the unlocked mode, input PC and press

user codes are deleted.

Note

：

T his operation will delete all user codes except programming code.

2.4.1 Set auto lock

：

I n the unlocked mode, input PC and press

confirming melody (The lock will automatically lock after being unlocked for 15 seconds).

2.4.2 Modify automatic locking time, in the unlocked mode, input PC and press

seconds. Input the new time (from 10 to 99 seconds) and then press

Then LED flashes green followed by a confirming melody.

2.4.3 Cancel auto lock

：

I n the unlocked mode, input PC and press

confirming melody.

2.5.1 Set Mute mode: In the unlocked mode, input PC and press

2.5.2 Cancel Mute mode

：

I n the unlock mode, input PC and press

confirming melody.

3.1.1 In the unlocked mode, input PC and press

the new remote control within 10 seconds. Then LED flashes green followed by a confirming melody.

Note

：

T he remote control will remain as the previous program if you fail to complete any one of above steps.

3.2.1 In the unlocked mode, input PC and press

remote controls are deleted.

4.1.1 In the unlocked mode, input PC and press

and press

to store the new PC within 10 seconds. LED flashes green followed by a confirming melody.

4.2.1 Remove one of the batteries and follow by pressing any one button 3 times to eliminate the remaining power, then press and hold

0 button, insert the batteriy, release the

the

○

5.1.1 In the unlocked mode, input PC and press

the new UC. LED flashes green followed by a confirming melody.

5.1.2 Provide temporary user his/her code, but keep a record for yourself in order to delete later on.

5.1.3 When this code is no longer needed, delete the temporary user code (see steps above).

I f LED flashes red, this indicates an error or failed operation. Please refer to the above instructions to confirm

specific error.

OPERATING STEPS

1 and

and

○

to store the new UC. Then LED flashes green followed by a confirming melody.

2 and

and

○

, Then LED flashes green followed by a confirming melody. The user code is now deleted.

3 and

and

○

8 and

and

○

9 and

and

○

0 and

and

○

0 button after you hear 3 beeps. The preset PC is now recovered.

○

1 and

and

○

Programming Code: xxxx

User Code A: xxxx

User Code B: xxxx

button, then insert the final battery into the interior receiver module.

. The LED flashes green.

, The LED flashes green followed by a confirming melody. All

4 and

and

○

, the LED flashes green followed by a

5 and

and

○

, LED flashes green for ten

to store.

6 and

and

○

, LED flashes green followed by a

7 and

and

, LED flashes green one time.

○

7 and

and

○

, LED flashes green followed by a

, point the new remote control to LED and press any button on

. LED flashes green followed by a confirming melody. All

. When LED flashes green, enter the new PC (up to 4-10 digits)

. LED flashes green. Enter a new UC and then press

EDA-33

STICKER

xxxx.xx.xx

to store