Gama Garden GT- 390 GT- 395 Інструкція з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Румпель Gama Garden GT- 390 GT- 395. Gama Garden GT- 390 GT- 395 14 сторінок. Petrol powered cultivator

Друкувати сторінку

2.2 Order of adjustment (for the following model: GT

395)

1. Press clutch lever out to 1/3 of the free escapement (Figure 6).

2. W ith the lever held in this position, draw the starter cord

slowly 2 or 3 times. The cultivator blades should start moving.

Screw off retaining nut of adjusting sleeve (Figure 6, Item 1).

While turning the sleeve (Figure 6, Item 2) as compared to the

body (Figure 6, Item 3), determine the play of the cable as

compared to the wiring. Screw in the retaining nut.

Order of adjustment (reverse)

1. Press out and fix the reverse lever (for the following model: T

395 OHV 7.0, T 395 BS 7.5).

2. Press clutch lever out to 1/3 of free escapement (Figure 5).

3. W ith the lever held in this position, draw the starter cord

slowly 2 or 3 times. The cultivator blades should start moving

If the blades do not rotate:

Screw off retaining nut of adjusting sleeve (Figure 6, Item 1).

While turning the sleeve (Figure 6, Item 2) as compared to the

body (Figure 6, Item 3), determine the play of the cable as

compared to the wiring. Screw in the retaining nut

Assembly of the adapter

1. In the front part of the cultivator, with a 13-mm key (purchased

separately), screw off the M8 nut, remove the flat washer,

retaining washer, and after removing the М8х65 screw, take

out the adapter from transportation position.

2. Install the adapter with its flat part in the internal part of left

side of frame (Figure 7) and fit the fixing holes of adapter and

frame together.

Adapter

3. From one side of the frame, insert the М8х65 bolt in the holes

fitted together, while from the other side of the frame insert the

flat washers, the retaining washers on the bolts, and screw the

M8 nut with 13-mm key.

Assembly of the plough iron bracket

1. Tilt the cultivator, leaning the adapter against a solid surface.

2. Screw off two М10 nuts in the rear part of the frame with 17-

mm key (purchased separately), take off flat washer, retaining

washers, and after removing М10х75 bolts, take off plough iron

bracket together with plough iron (Figure 8).

3. Place a flat washer each on the М10х75 bolts.

4. Insert the plough iron bracket at the half of the engine frame,

and fit together the fixing holes found on the bracket and the

frame. Insert the bolts with washers in the holes.

5. Put the flat washers, retaining washers on the bolts, and screw

in the М10 nuts. Screw in the nut with a 17-mm key.

Assembly of the plough iron:

1. Set the plough iron (Figure 8) and the plough iron bracket

with wheels upwards.

2. In order to adjust the tilling depth, fit the holes on the plough

iron bracket with one hole of the plough iron, put in the fastener,

and fix it with cotter pin.

Bolts

Figure 7

Properly

mounted

plough iron

For efficient work performance, make sure that the

Note:

plough iron is properly located as compared to the plough iron

bracket

(Figure 8).

5. Assembly of blades

Mount the blades on the external, central and internal blade

holders by means of М8х25 bolts, Ш8 retaining nut and М8 nut

(Figure 9). This component is installed from the right in the

direction of travel. When installing the component, make sure

that cutting edge of blades are set in accordance with the

cultivator's direction of travel. If the component is properly

assembled, then the curve of the blade nearer to the reducer will

show from the reducer to the driver

The left side element must be assembled in the same way, in

opposite-hand view.

Note: on the blades of the component,

embossed letters (L), (R) are found, meaning L- left-side blade,

R-right-side blade.

Internal blade

holder

Central blade holder

External blade holder

Installation of blades

1. Put the internal blade holders (with blades installed) on the

reducer shaft (Figure 10, Item 3) from both sides, fit the holes

of the reducer shaft and the blade holders together, and fix

them with fasteners and cotter pins (Figure 10, Item 1, Item 2).

Figure8

Internal blades

assembled

Central blades

assembled

External blades assembled

Figure 9