Gama Sonic 94B002 Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Ліхтар Gama Sonic 94B002. Gama Sonic 94B002 4 сторінки. Victorian bulb solar lamp post

Друкувати сторінку

Assembly Instructions

94B001

1. Using the provided template, mark and drill three holes into concrete

no larger than the provided anchors (G).

NOTE: For installation in the ground where pouring concrete is not preferred or

possible, use our EZ Lamp Post Anchor, model 30001 (sold separately) to quickly and

easily secure the lamp anywhere in your yard. This is only to be used with model

94B001.

2. Place the anchors (G) into the holes with

the threaded ends facing up.

3. Place the Base Pole (F) over the

anchors and secure using a wrench.

Cover the nuts with the provided

plastic covers.

4. Place the middle pole (E) on top of

the base pole (F) and secure with the

provided screws.

5. Attach the top pole (D) to the middle

pole (E), and the spacer pole (C) to the

top pole (D) by screwing the poles

clockwise.

6. Attach the ﬁxture (B) to the spacer

pole (C) by twisting clockwise.

94B002/94B003

1. Using the provided template, mark and drill three holes into concrete

no larger than the provided anchors (G).

above for steps 1-5)

2. Place the anchors (G) into the holes with the threaded ends facing

up.

3. Place the Base Pole (F) over the anchors and secure using a wrench.

Cover the nuts with the provided plastic covers.

4. Place the middle pole (E) on top of the base pole (F) and

secure with the provided screws.

5. Attach the top pole (D) to the middle pole (E),

and the spacer pole (C) to the top pole (D) by

screwing the poles clockwise.

6. Remove the ﬁnial cap (K) from the centerpiece

(H/I) by removing the screws.

7. Insert one of the ﬁxtures with arms (J) into the

centerpiece (H/I).

8. Screw in two bolts through the holes in the arm (J)

into the centerpiece (H/I) using the supplied hex

wrench.

9. Secure the two bolts using a nut inside the

centerpiece (H/I)

10. Repeat the installation for the second and third

lamp head (only second if installing double head

lamp).

11. Replace the ﬁnial cap (K) on the centerpiece (H/I) and

secure using the screws removed earlier.

12. With the help of another person, place the

assembly of lamp heads and centerpiece

(H/I) on top of the spacer pole (C) and twist

clockwise until fully attached to the pole.

page 3

(follow along with illustration

Operation Instructions

Remove the top (A) from the Fixture by removing the two screw

caps.

Install the GS Solar LED Bulb by holding it by the base and twisting

it clockwise into the socket.

Replace the top (A) back on the ﬁxture and secure with the two

screw caps.

Using the external switch, select your desired setting.

Low = Softer light output and longer duration

High = Brighter light output

The lamp will operate automatically at dusk.

Replacement Parts

Replacement Batteries and Bulbs are available at

www.gamasonic.com or via our Toll Free number: +1-800-835-4113

Your Lamp can use the following bulbs:

C37WW10W – included bulb with Warm White LEDs (2700K)

C37BW10W – bulb with Bright White LEDs (6000K)

F30WW05W – Flame bulb with simulated ﬂame LEDs

T45WW10W – Edison LED Bulb with Warm White LEDs (2700k)

Your Lamp uses the following batteries:

GS32V30