Adesys Octalarm EM-8001 Швидкий старт - Сторінка 3
Переглянути онлайн або завантажити pdf Швидкий старт для Блок управління Adesys Octalarm EM-8001. Adesys Octalarm EM-8001 4 сторінки.
Друкувати сторінку
2.
I nstallation
2.1.
Mounting the external module (EM-8001)
The EM-8001 can be mounted to the wall and to 35 mm DIN rails.
When mounted to a DIN rail, the module can easily be used in system
cabinets.
2.2.
Connecting the external module (EM-8001)
Powered by Octalarm-Touch
To connect the EM-8001 to the Octalarm-Touch, you need a 2-pair,
4-core cable. The cores are for:
•
Pair 1: signal line A and B;
•
Pair 2: power supply and ground wire.
The wiring diagram is shown on the front sticker.
When using the relay, an external power supply is required.
External power supply
When using the EM-8001 with an external power supply, you need a
1-pair, 3-core cable. The cores are for:
•
Pair 1: signal line A and B;
•
Core: ground wire.
The wiring diagram is shown on the front sticker.
The power supply wire of the Octalarm-Touch must not be connected to
the EM-8001.
Signal lines for both power supply modes
The wires must be connected to the connector corresponding to the
marking on the front sticker. The final EM-8001 on the bus will have
to be terminated with a 120 ohm resistor. The EM-8001 features an
integrated resistor: simply connect the 'R' and 'B' externally on the
screw connector.
EM-8001 / Octalarm-Touch wiring diagram
2.3.
Slave ID
The EM-8001 works with a master/slave structure, in which the
Octalarm-Touch acts as the master and the EM-8001 as the slave.
Slaves must have a unique Slave ID.
To set the Slave ID on the modules, all you need is a screwdriver.
When turning the screw, the LED above the corresponding input
number will turn blue, corresponding to the selected Slave ID.
Led status indication (idle)
Number of flashes in idle
1x
Slave ID 1
2x
Slave ID 2
3x
Slave ID 3
4x
Slave ID 4
2.4.
Power supply
When mounted close together, the EM-8001 can be powered by the
Octalarm-Touch. When the units are further apart (> 100 m), it is
recommended to always use an external power supply. This external
power supply must meet the prescribed specifications and can be
connected to the V and ground. Adésys can supply the SV-19 (DIN-
rail-mounted power supply) or the SV-20 (mains adapter) for this
purpose.
When using the relay, an external power supply is required.
3.
Safety rules
To use the EM-8001 properly, please read and follow these safety
rules:
•
mount the device on a solid panel or wall;
•
protect the EM-8001 against a surge by using a grounded power
connection;
•
use the EM-8001 in an indoor setting, the device needs to be
protected form direct weather exposure;
•
the operating temprature is -30°C ... 70°C. Using the EM-8001
outside this temperature range my result in damage;
•
this equipment is not suitable for use in locations where children
are likely to be present.
4.
Storage and transport
•
There must be no flammable or explosive materials nearby.
•
The temperature must be within the -40°C ... 85°C range.
•
Do not store this product in a place exposed to direct sunlight.
5.
Faults and repair
When a fault has occurred please contact Adésys service helpdesk.
By opening the Octalarm-Touch the warranty is void. Repairing the
Octalarm-Touch is only allowed by Adésys appointed experts.
6.
Disposal
The EM-8001 is an electronic device. Electrical and electronic
equipment should not be mixed with general household waste.
Please contact the installer or Adésys for more information.
7.
Guarantee and liability
Every EM-8001 undergoes a series of extensive tests at Adésys prior
to dispatch. Adésys also gives a two year guarantee.
The guarantee becomes invalid if:
•
the defect is caused by gross negligence or incompetent
installation;
•
the appliance has been repaired and/or altered without Adésys'
permission;
•
it is established that the serial number has been removed or
damaged.
Adésys accepts no liability whatsoever for consequential damage
caused by incompetent use of and/or malfunctions in the EM-8001.