HIKOKI C361395R Інструкція з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Дриль. HIKOKI C361395R. HIKOKI C361395R 16 сторінок.

Друкувати сторінку

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

ROTARY HAMMER SAFETY

WARNINGS

Safety instructions for all operations

1. Wear ear protectors

Exposure to noise can cause hearing loss.

2. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

3. Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

Safety instructions when using long drill bits with

rotary hammers

4. Always start drilling at low speed and with the bit tip

in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

5. Apply pressure only in direct line with the bit and do

not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. Do not touch the bit during or immediately after

operation. The bit becomes very hot during operation

and could cause serious burns.

5. Before starting to break, chip or drill into a wall, ﬂ oor or

ceiling, thoroughly conﬁ rm that such items as electric

cables or conduits are not buried inside.

6. Always hold the body handle and side handle of the

power tool ﬁ rmly. Otherwise the counterforce produced

may result in inaccurate and even dangerous operation.

7. Wear a dust mask

Do not inhale the harmful dusts generated in drilling or

chiseling operation. The dust can endanger the health of

yourself and bystanders.

8. Mounting the tool

○ To prevent accidents, make sure to turn the switch oﬀ

and disconnect the plug from the receptacle.

○ When using tools such as bull points, drill bits, etc.,

make sure to use the genuine parts designated by our

company.

○ Clean the shank portion of the tool.

○ Check the latching by pulling on the tool.

9. To prevent accidents, make sure to turn the switch oﬀ

and disconnect the plug from the receptacle when the

drill bits and other various parts are installed or removed.

The power switch should also be turned oﬀ during a work

break and after work.

10. Rotation + hammering

Using drill bit holder (standard accessories)

When the drill bit touches construction iron bar, the bit

will stop immediately and the rotary hammer will react to

revolve. Therefore ﬁ rmly tighten the side handle.

11. Rotation only

To drill wood or metal material using drill chuck holder

(standard accessories)

○ Application of force more than necessary will not only

expedite the work, but will deteriorate the tip edge of the

drill bit and reduce the service life of the rotary hammer

in addition.

○ Drill bits may snap oﬀ while withdrawing the rotary

hammer from the drilled hole. For withdrawing, it is

important to use a pushing motion.

○ Do not attempt to drill anchor holes or holes in concrete

with the machine set in the rotation only function.

○ Do not attempt to use the rotary hammer in the rotation

and hammering function with the drill chuck holder

attached. This would seriously shorten the service life of

every component of the machine.

12. Hammering only

Using drill bit holder (standard accessories)

13. Make sure to securely hold the tool as shown in Fig. 13

during operation.