HIKOKI C 6MEY Інструкція з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Пила. HIKOKI C 6MEY. HIKOKI C 6MEY 16 сторінок.

Друкувати сторінку

(*1) About the mode select function

Each time the mode selector switch is pushed, the

operation mode changes.

When Silent mode is selected, the Silent mode indicator

lamp lights up.

Silent mode reduces maximum motor RPM enabling

eﬃ cient work with less noise.

If the load increases while the motor is operating in

Silent mode, it automatically changes to Power mode.

Additionally, if the load decreases again, it automatically

returns to Silent mode.

In Power mode, no change is made to Silent mode even

when the load decreases.

Mode

Power

Silent

Safeguard Function

Overburden Protection

Temperature Protection

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade

Since use of as dull saw blade will degrade eﬃ ciency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very "heart" of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer of this agent in order

to avoid a safety hazard.

5. Maintenance of lower guard

For safe and proper working, always keep the machine

and ventilation slots clean. The lower guard must

always be able to more freely and retract automatically.

Therefore, always keep the area around the lower guard

clean. Remove dust and chips by blowing out with

compressed air or with a brush.

6. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

7. Storage

Please avoid locations such as the following for the

storage of products and accessories that are not being

used, and store them in a safe and dry place.

NOTE

○ Do not store them in locations where children can

reach them or easily get hold of them.

○ Do not store them in locations where rain can fall

such as under the eaves of a house, or where there

is humidity.

No-load speed

4100 /min

2500 /min

LED Light Display

On 0.1 second/oﬀ 0.1 second

On 0.5 second/oﬀ 0.5 second

NOTE

○ You cannot change the mode unless the power plug is

connected to a receptacle and the switch is pulled once.

○ Even if the switch is turned on and oﬀ or the power plug

is disconnected and connected, this unit will maintain the

mode that you set.

LED LIGHT WARNING SIGNALS

(Fig. 27)

This product features functions that are designed to protect

the tool itself. While the switch is pulled and 3 seconds after

its release, if any of the safeguard functions are triggered

during operation, the LED light will blink as described in

Table 1. When any of the safeguard functions are triggered,

immediately remove your ﬁ nger from the switch and follow

the instructions described under corrective action.

Table 1

Remove the cause of the overburdening.

Allow the tool to thoroughly cool.

○ Do not store them in locations where there are

sudden changes in humidity or there is direct

sunlight.

○ Do not store them in locations where there are

volatile substances which have a risk of catching ﬁ re

or exploding.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

NOTE

Due to HiKOKI's continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Corrective Action