Green Blue GB520 Посібник - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник для Метеостанція Green Blue GB520. Green Blue GB520 14 сторінок. Wireless home weather station
Друкувати сторінкуtemperature and humidity a7: weather forecasting. PART B-back button and power b1:
mem button b2: snooze/light button b3: time button b4: alarm button b5: up button b6:
down button b7: alert button b8: hpa/inhg button b9: alarm on/off shift switch b10:
backlight hi/lo" shift switch b11: usb charger output socket b12: dc power input socket
b13: battery compartment PART C-wireless outdoor sensor
03. Initial operation • Open Weather Station battery compartment cover. • Insert 2 x AA
batteries observing polarity [ + and – marks] • When you insert the batteries, all the icon
on the LCD display will briefly light up for 3 seconds, and you will hear a beep tone, and
detect indoor temperature & humidity. • The Weather Station will now start to make
a connection to the outdoor remote sensor. This operation takes about 3 minutes and is
displayed by a flashing reception RF antenna symbol in the "OUTDOOR" display area on
the receiver. • This now, replace Wireless Outdoor Sensor battery compartment cover,
Open Weather Station battery compartment cover ,Insert 2 x AA batteries observing
polarity [ + and – marks] • After receiver has created a connection to the outdoor remote
sensor, it will then b enters the Radio control time receive mode.
04. Reception of the Radio signal: The clock automatically starts the DCF signal search
after 7 minutes of any restart or changing of new fresh batteries. The radio mast icon
starts to flash. • At 1:00 /2:00 / 3:00 am, the clock automatically carries out the
synchronization procedure with the DCF signal to correct any deviations to the exact time.
If this synchronization attempt is unsuccessful (the radio mast icon disappears from the
display), the system will automatically attempt another synchronization at the next full one
hour. This procedure is repeated automatically up to total 5 times. • To start manual DCF
signal reception, press and hold down the UP button for two seconds. If no signals
received within 7 minutes, then the DCF signal search stops (the radio mast icon
disappears) and start again at the next full one hour. • During RC reception, to stop
searching radio signal, press the UP button once.
F.Y.I A flashing radio mast icon indicates that the DCF signal reception has started
• A continuously displayed radio mast icon indicates that the DCF signal was received
successfully • We recommend a minimum distance of 2.5 meters to all sources of
interference, such as televisions or computer monitors • Radio reception is weaker in
rooms with concrete walls (e.g.: in cellars) and in offices. In such extreme circumstances,
place the system close to the window. • During the RC receive mode, only the
SNOOZE/LIGHT and UP button function, other button operation have no function, If you
want to carry out other functions of operation, please press "-" button to exit the
RC receiving mode.
Manual time setting: • Press once TIME button, can switch the display calendar or
second • Press and hold down the TIME button for 2 seconds, the 12/24 hour mode
- 02 -
display starts to flash. Now use + and - buttons to set the correct 12/24 hour mode.
• Press TIME to confirm your setting, the Time zones start to flash, Now use UP and DOWN
buttons set a correct time zone (-12 to +12). • Press TIME to confirm your setting, the Hour
display starts to flash. Now use UP and DOWN buttons to set the correct hour. • Press TIME
to confirm your setting, the Minute displays starts to flash. Now use UP and DOWN buttons
to set the correct minute.• Press TIME button to confirm your setting, the Month and Date
icon display starts to flash. Now use UP and DOWN buttons to set the date display on
Month/Date or Date/Month • Press TIME button to confirm your setting, the Year display
2014 starts to flash. Now use UP and DOWN buttons to set the correct year. • Press TIME
button to confirm your setting, the Month display starts to flash. Now use UP and DOWN
buttons to set the correct month • Press TIME button to confirm your setting, the Date
display starts to flash. Now use UP and DOWN buttons to set the correct date • Press TIME
button to confirm your setting, the language selection for the Weekday displays starts to
flash. Now use + and - buttons to select a language • Press TIME to confirm your setting
and to end the setting procedures, enter the clock mode.
F.Y.I. After 20 seconds without pressing any button, the clock switches automatically from
Set Mode to Normal Time Mode. There are 7 languages of Weekday: English, German,
Italian, French, Spanish, Dutch and Danish.
Setting the daily alarms: Press once ALARM button, can switch the display calendar or
alarm time • Press and hold down ALARM button for 2 seconds until Alarm Time hour
display of the Alarm time starts to flash. Use the UP and DOWN buttons to set the required
hour • Press ALARM button to confirm your setting, The Minute display of the Alarm time
starts to flash. Use the UP and DOWN buttons to set the required minute. • Press ALARM
button to confirm your setting and to end the setting procedure. F.Y.I. After 20 seconds
without pressing any button the clock switches automatically from setting mode to Normal
clock mode.
The alarm for opening and closing: Product back of the ALARM shift switch is pushed in
the ON position, LCD display the "Ring" icon, the alarm function is open, at the same time,
the alarm time display in the calendar bar • Product back of the ALARM shift switch is
pushed in the OFF position, the "Ring" icon disappears, the alarm function is close, at the
same time, the calendar bar display calendar F.Y.I.: The alarm will sound for 2 minutes if
you do not deactivate it by pressing any button. In this case the alarm will be repeated
automatically after 24 hours • Rising alarm sound (duration: 2 minutes) changes the
volume 4 times whilst the alarm signal is heard.
• Switching off the alarm signal: Press any button except the "SNOOZE/LIGHT" button to
stop the alarm signal. It is not necessary to reactivate the alarm. It switches itself
automatically to the alarm time which has already been set.
-03-