Green Brook TUBH2 Інструкція з експлуатації - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Обігрівач Green Brook TUBH2. Green Brook TUBH2 2 сторінки. Tubular heaters

Друкувати сторінку

IMPORTANT INFORMATION

1. This heater must be installed in accordance with the Building Regulations. These may be

obtained from HMSO or viewed and downloaded from www.communities.gov.uk

following the link for Building Regulations.

2. If in any doubt consult a qualified electrician.

3. This heater is designed for wall mounting and must be used horizontally, this heater should

not be used vertically and should not be used as a free standing portable appliance.

4. If the heater is to be installed in a location where it may be touched, or could cause

injury, we recommend fitting a protective guard which is designed specifically for this

purpose (Part no: TUBG).

5. This heater must be installed so that switches and other controls cannot be touched by a

person in the bath or shower.

6. The mounting position should allow the free movement of air around the heater.

Obstructing the air flow could result in overheating.

7. Switch off the mains before commencing installation and remove the appropriate circuit

fuse.

8. Suitable for indoor use only.

9. This product is suitable for installation on surfaces with normal flammability (indicated by

the "F" in a triangle) e.g. wood, plasterboard, masonry. It is not suitable for use on highly

flammable surfaces (e.g. polystyrene, textiles).

10. Before making fixing hole(s), check that there are no obstructions hidden beneath the

mounting surface such as pipes or cables.

11. The chosen location of your new heater should allow for the product to be securely

mounted (e.g. to a solid wall) and safely connected to the mains supply.

12. Do not site the heater directly beneath a mains outlet socket.

13. If the location of your new heater requires the provision of a new electrical supply, the

supply must conform with the requirements of the Building Regulations.

14. This product is designed for use with a permanent connection to fixed wiring, this should

be either a suitable ring circuit (protected with a 5 or 6 Amp MCB or fuse) or a fused spur

(with a 3 Amp fuse) via a fused connection unit. The supply must incorporate a switch or

other means of disconnection.

15. Make connections to the electrical supply in accordance with the following code:

Live-Brown or Red

Neutral-Blue or Black

Earth-Green and Yellow

16. If the supply cord is damaged, it must be replaced by a qualified persons in order to

avoid a hazard.

17. If you have made a fixed connection to the mains, you are advised at every stage of your

installation to double check any electrical connections you have made. After you have

completed your installation there are electrical tests that should be carried out, these tests

are specified in the Wiring Regulations (BS7671) referred to in the Building Regulations. If in

doubt consult a qualified electrician.

18. This product is not intended to be used by

and/or mental impairments that would prevent them from using it safely.

WARNING - To avoid overheating, do not cover the heater. This product becomes hot!

NOTE:

You may experience a smoke vapour when heater is first switched 'On', this is

caused by a protective coating, this will clear after two minutes.

children and persons with sensory, physical

INSTALLATION INSTRUCTIONS

Single Heater:

1. Choose the location for your new heater giving consideration to all of the points above.

2. Fit the plastic clips onto the fitting and slide towards each end of the heater. See below

for assembly diagram.

3. Hold the heater against the mounting surface and mark the position of the fixing holes.

4. Remove the plastic clips.

5. Use a spirit level to check holes are level.

6. Make fixing holes using a No.8/5mm drill bit.

7. Insert the plastic plugs and secure the bottom part of the clip using screws supplied.

If the screws supplied are not appropriate for your installation, choose suitable

alternatives.

8. Rest the heater onto the plastic clips and secure in place.

9. Make connections to the mains supply according to the colour code opposite or plug

in.

10. Restore the power supply and switch on.

Multiple Heaters:

1. Follow the directions for fitting of a single heater for each of the locations where a

heater is required. Do not fit one heater directly above another.

2. Loosen the screw in the end of the heater and remove the end cap. Take care

removing the end cap not to pull the wires out of the terminals. Ease the cable back

through the gland/nut as you pull the end cap away.

3. Cut out required blank cable entry and fit a cable gland. The gland should be inserted

with the short thread entering the cap and the large nut remaining on the outside.

4. Tighten securely but take care not to overtighten.

5. Check the length of cable required between the two heaters and cut to length giving

sufficient spare to enter the first heater.

6. Loosen the new cable gland/nut and thread the cable through.

7. Strip back the cable end with approximately 25mm of coloured insulation showing and

approximately 5mm of bare conductors.

8. Make the connections to the heater making sure that both supply and through

connections are secure and that there are no strands of wire protruding from the

terminal block.

9. Secure the spare cable clamp in position using the screws provided.

10. Secure the plastic end cap back in position threading both cables back through the

gland/nuts.

50mm minimum