Centurion RDO-10A Інструкція з монтажу та посібник користувача - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу та посібник користувача для Відкривач гаражних дверей Centurion RDO-10A. Centurion RDO-10A 13 сторінок. Roller door opener
Друкувати сторінкуThe procedures outlined in this manual require a degree of technical and mechanical skill. The Opener
should always be installed and adjusted by a technically qualified person. It is not recommended to be
installed by a home handyman. Never install the Opener on a poorly adjusted or worn garage door.
1. Check for Correct Function of the Garage Door
Before commencing installation of the Opener check that the garage door is functioning correctly. It must be well balanced
and operate smoothly and freely and not bind or stick in the side tracks nor make contact with any supporting members.
When released from any position it should not rise or fall more than 100mm. The effort required to open or close the door by
hand should not exceed 150N (15kg).
2. Check Side Room Requirement
The min and max mounting positions, as measured from the edge of the door curtain to the inner edge of its mounting
bracket, are 40 and 50mm. (Fig.1)
If the distance is less than 40mm or more than 50mm then door bracket must be moved so as to fall within the bounds of
these 2 dimensions.
3. Select Installation Side
Determine to which end of the door the Opener will be installed and select the dip switch according to the following:
Left Hand Side Installation ‐ Dip 6 "ON" (Fig.7‐G) Right Hand Side Installation ‐ Dip 6 "OFF" (Fig.7‐G)
Note – Installation side is referred to as "inside looking out"
4. Fit Opener to Door (right hand installation described)
Remove or render inoperative all existing locks and ropes.
Select the side of the door to which the Opener will be fitted
Ensure that the door bracket, to which the Opener will be installed, is the correct distance from the edge of the curtain.
Open the door fully and ensure that the door stoppers have engaged with track stoppers.
Place a prop under the door as close to the edge as possible and is adjusted so that it sits firmly under the garage door. (Fig.2)
Check U‐bolt on opposite side of door and ensure that it is securely tightened.
Remove the (Opener side) U‐bolt from the door bracket and then remove the door mounting bracket from the wall.
Orient the Opener so that its 2 forks line up with the narrowest of the garage door drum wheel spokes.
Slide the Opener onto the door axle and push it fully into the door so that it sits against the drum wheel. (Fig.2)
Refit the door mounting bracket to the wall making sure to tighten the mounting bracket screws securely. (Fig.3)
Insert the U‐bolt supplied through the Opener and door bracket slots and then secure with the nuts and washers provided.
Check the manual operation of the door by fully raising and lowering it several times and ensure it runs smoothly and does not
catch on any part of the Opener
5. Pin Curtain to Drum Wheel
The door curtain must be secured to the drum wheel with self drilling screws at both sides of the door.
With the door fully closed, mark the curtain at points "A" and "B" ensuring that the fixing points are at least 90 deg apart.
(Fig.4)
Open the door slightly so as to have access to the marked positions then secure the curtain to the drum wheel as depicted.
Ensure screws do not interfere with the running of the door or operator.
6. Fit Weight Bar
Securely fix the weight bar to the top edge of the door rail with the screws and nuts provided. (Fig.5)
7. Attach Entrapment Warning Label
Attach the Entrapment Warning Label to the wall in a prominent position adjacent to the Opener. (Fig.5)
8. Connect to Power Supply
Connect to a properly earthed power supply using the power cord provided. (Fig.5)
Important Note: Ensure that the power cord does not touch the moving door and that no excess cord hangs below the
Opener when it is plugged in.
The Opener is now installed and ready for adjustment.
INSTALLATION INSTRUCTIONS
- 4 -