Brita 3-Way Water Filter Dispenser System Інструкція з використання Посібник з використання - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з використання Посібник з використання для Сантехнічний виріб Brita 3-Way Water Filter Dispenser System. Brita 3-Way Water Filter Dispenser System 13 сторінок. 3-way water filter dispenser

Друкувати сторінку

BRITA 3-Way Water Filter Dispenser –

easy installation

Before starting, please check that you have all the components

listed above (see ﬁ g. 1) as well as the recommended tools.

There are 7 steps to the installation.

Prior to installation, read the Technical Data (chapter 7) and

the Important Information (chapter 9). The system cannot

be installed with a low pressure boiler as this might lead to

water damages.

After storage and transport below 0°C, the product must be

stored in the open original packaging for at least 24 hours at

the stated ambient temperatures (chapter 7) for operation.

3.1

Step 1: Selecting the carbonate hardness

setting (++/+) on the ﬁ lter head

The ﬁ lter head has been set to meet most European water con-

ditions. In some soft water areas though, you may wish to adjust

the ﬁ lter head to your local settings. To do so, ﬁ rst carry out a

carbonate test using the supplied testing strip. The strip can be

found in the outer wrapping of these Usage Instructions.

Using the testing strip:

• Let the red response ﬁ eld of the probe soak in a glass of your

tap water for 1 second (ﬁ g. 2).

• After 1 minute, compare the colour of the response ﬁ eld with

the table and read the appropriate setting from the table.

Depending on the colour of the testing strip, we recommend

setting your ﬁ lter head as follows:

Setting

Red, orange,

Colour

yellow

Capacity

1000 L

German Carbonate

up to 8.5

Hardness [°dH]

English Carbonate

up to 10.6

Hardness [°eH]

Green, dark

green

500 L

above 8.5

(ﬁ g. 2)

above 10.6

Setting

French Carbonate

up to 15.2

Hardness [°fH]

Grains per Gallon CaCO3

up to 8.9

[gpg CaCO3]

Milligram per Litre CaCO3

up to 151

[mg/L CaO3]

The ﬁ lter head is set to "++" by default. To change the setting,

use an Allen key (4 mm). Turn in the direction of the arrow until

the "+" appears in the window (ﬁ g. 3).

The ﬁ lter head contains a ﬂ ow regulator already installed which

guarantees smooth water ﬂ ow from your dispenser even at higher

water pressures.

3.2

Step 2: Starting the BRITA electronic

cartridge exchange indicator

A Commissioning:

Please insert the enclosed batteries (2 x AA) into the appropriate

compartment of the BRITA electronic cartridge exchange indicator

with display. A long beep will sound after insertion of the batteries.

B Initial programming with ++ or + setting (see step 1):

Important: The BRITA electronic cartridge exchange indicator has

been set to 90 days to co-ordinate with the cartridge ﬁ ltration set-

ting of "++". Both of these default settings will deliver optimum

ﬁ ltration performance for most water conditions.

Caution: Please, ensure that you activate the electronic BRITA

cartridge exchange indicator with display during the day so that the

signal can start during the day.

Initial programming with ++ setting (see ﬁ g. 4):

a Press the DISPLAY button brieﬂ y to activate the display. Initially,

the default setting of 90 days is displayed.

b Then press the START/RESET button brieﬂ y to activate the

90-day timer.

c A ﬂ ashing spot in the bottom left of the display indicates that the

timer has begun.

Initial programming with + setting (see ﬁ g. 4):

a Press the DISPLAY button brieﬂ y to activate the display. Initially,

the default setting of 90 days is displayed.

b Press and hold the DISPLAY button and then press the

START/RESET button brieﬂ y at the same time. This activates

the setting mode.

above 15.2

above 8.9

above 151

(ﬁ g. 3)

ENGLISH