CENTURION SYSTEMS G-ULTRA Короткий посібник - Сторінка 2
Переглянути онлайн або завантажити pdf Короткий посібник для Вимірювальні прилади CENTURION SYSTEMS G-ULTRA. CENTURION SYSTEMS G-ULTRA 2 сторінки.
Друкувати сторінку
10.1.2. Removing the Fascia
The fascia can be removed by inserting the tips of one's fingers into the
slots (as shown in Figures 4 and 5), and pulling outward and upward.
The fascia should pop off without effort.
G-ULTRA Fascia
Slots
FIGURE 4
G-ULTRA Fascia
Main G-ULTRA
Unit
FIGURE 5
Reverse the procedure under Section 10.1 to re-assemble the
G-ULTRA.
10.2. Installation
10.2.1. Wall-mounting
The Mounting Plate is used to mount the G-ULTRA device to a wall. Use four
screws with wall anchors(not supplied) to secure Mounting Plate.
Mounting
screws
(Not Supplied)
Wall
anchors
Mounting
Plate
FIGURE 6
Clip the G-ULTRA main unit into the Mounting plate after it has been
secured to the wall; a 'click' will be heard if done correctly.
G-ULTRA
Mounting
Main Unit
Plate
FIGURE 7
10.2.2. DIN Rail-mounting
Should the G-ULTRA need to be mounted onto a DIN-rail, a DIN-rail
mounting kit is available. Ask at Centurion Systems (Pty) Ltd for more
information.
Secure the DIN-rail clips to the back of the mounting plate using four (4)
screws.
Mounting
Plate
DIN-rail
Mounting
Screws
Clips
FIGURE 8
Position the bottom of the DIN-rail clips onto the rail, and clip the top end
into position(A). A 'click' will be heard if it has been done correctly(B). Clip
the G-ULTRA main unit into the Mounting plate after it has been secured to
the wall; another 'click' will be heard if done correctly.
DIN-rail
DIN-rail
DIN-rail
Clip
'click'
A
B
Mounting
DIN rail
Plate
Clip
FIGURE 9
To remove the unit from the DIN-rail, remove the G-ULTRA main unit from the
mounting plate as described in Section 10.1. Insert a small flat screwdriver
into the hole(s) shown in Figure 10, and gently pry the clips from the rail.
Holes for
Mounting
Screwdriver
Plate
DIN Rail
FIGURE 10
10.3. Configuration
1. Complete the wiring of the unit as per Section 8 and 10.4 of this
document.
2. Power up the device and verify that the device connects to the G-WEB
platform by referring to the LCD home screen.
3. Navigate your Internet browser to http://www.gweb.co.za
(or www.g-web.com.au for Australia and New Zealand) and login to your
existing profile or, alternatively, register a new profile.
4. On the My Devices page, select Add New G-ULTRA Device and follow the
onscreen instructions to associate the device to your profile.
5. Configure the device with the desired settings using your online portal.
Quick Add:
To instantly associate a device to your online profile, scan
the QR code using your mobile phone and any universal QR
scanner mobile application.
10.3.1. G-WEB
All features – both basic and advanced – can be easily, and remotely,
configured via the G-WEB online interface. By simply logging into G-WEB
using any Internet-enabled device, one can add and delete devices, specify
text for input and output notifications and activations, modify device
characteristics and a plethora of other features, all from the comfort of one's
home or office. G-WEB can be accessed by navigating to http://www.gweb.
co.za (or www.g-web.com.au for Australia and New Zealand). Note that it
will be necessary to register if you have not previously done so.
10.3.2. SMS Commands
The table below lists the optional basic SMS commands available on the
G-ULTRA. All basic and advanced configurations can be done via the G-WEB
online portal.
SMS Command
Description
Device Status Request to which the device
will respond with the following information:
• IMEI
• I/O Status
P.XXXX
1
.STATUS
• Supply Voltage
• Firmware Version
• Signal Strength
• Relay Status
• Device date & time
Add New Phone Number which will by
P.XXXX.AP.Number
default pulse Relay 1 by missed call
Delete a specific access number from the
P.XXXX.DP.Number
G-ULTRA's memory
Switch output ON where Y is the
corresponding output number
P.XXXX.OUT.Y.ON
IO1 Y=1, IO2 Y=2, IO3 Y=3, IO4 Y=4,
RELAY1 Y=5, RELAY2 Y=6
Switch output OFF where Y is the
corresponding output number
P.XXXX.OUT.Y.OFF
IO1 Y=1, IO2 Y=2, IO3 Y=3, IO4 Y=4,
RELAY1 Y=5, RELAY2 Y=6
TABLE 4
1. XXXX = Device Default Password
10.4. Wiring Diagrams
Gate Status Monitoring
Do not mount close to DOSS sensor or remote receiver.
G-ULTRA
GND
IO1
IO2
IO3
IO4
NO
COM
NC
NO
COM
NC
Trigger (Pulse)
Do not mount close to DOSS sensor or remote receiver.
G-ULTRA
GND
IO1
IO2
IO3
IO4
NO
COM
NC
NO
COM
NC
Trigger - Pedestrian (Pulse)
Do not mount close to DOSS sensor or remote receiver.
G-ULTRA
GND
IO1
IO2
IO3
IO4
NO
COM
NC
NO
COM
NC
+ VDC -
+ VDC -
+ VDC -
D-Series
Controller
FIGURE 11
D-Series
Controller
FIGURE 12
D-Series
Controller
FIGURE 13