Gantner 776891 Інструкція з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Сенсорні термінали Gantner 776891. Gantner 776891 4 сторінки. Information terminal
Друкувати сторінку
Electrical connections
TCP/IP with external power supply
GAT Info 6100
3
Power supply
DC power (see technical data) supplied by a separate power supply unit
(LPS and SELV - Limited Power Source and Safety Extra Low Voltage) (1).
The power input is protected against reverse polarity.
Connection to the device front part
The socket (3) for the connection cable between the device front and rear
parts must be clean to ensure correct operation.
Relay output
No function.
Optocoupler input
No function.
Safety instructions
- This device must be installed by qualified personnel only.
- The applicable safety and accident prevention regulations
must be observed.
- Safety devices must not be removed.
- Please observe the technical data of the device specified
on the data sheet.
- The device must be disconnected from the power supply
prior to installation, assembling or dismantling.
This product is herewith confirmed to comply with the requirements set out
in the Council Directives on the Approximation of the laws of the Member
Statesrelating to Electromagnetic Compatibility Directive 2004/108/EG.
This product is in conformity with the following EC directives, including all
applicable amendments:
- 1999/5/EC (R&TTE directive)
- 2004/40/EC (Limitation of human exposure to electromagnetic fields)
- 2011/65/EU (Restriction of the use of certain hazardous substances in
electrical and electronic equipment)
The WEEE symbol on GANTNER products and their packaging indicates that the
corresponding material must not be disposed of with normal household waste. Instead,
such marked waste equipment must be disposed of by a designated electronic waste
recycling facility. Separating and recycling this waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information on recycling an item
marked with the WEEE symbol, please contact your local city office or your household
waste disposal operation.
Valid from July 1
, 2016 • Technical data subject to modification without notice!
st
4
DB_GAT-INFO6100--EN_12.indd • Part No.: 860380
Mains power
1
Power supply unit
2
TCP/IP
Network
Ethernet connection (2) via screw terminals.
Recommended cabling
Ethernet: min. CAT 5 (STP) for 100 MBit
Wiring standard
Ethernet 10/100 MBit
568A
TX +
green/white
TX -
green
RX +
orange/white
RX -
orange
Applicable for the following devices:
- GAT Info 6100 F
FCC NOTICE (Class B)
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, included interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning Statement
[Any] changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
GANTNER is committed to meeting or exceeding the requirements of the
RoHS directive (2011/65/EU). The RoHS directive requires that manufacturers
RoHS
eliminate or minimize the use of lead, mercury, hexavalent chro-mium, cadmium,
polybrominated biphenyls and polybrominated diphenyl ethers in electrical and
C OMP LI A N T
electronic equipment sold in the EU after July 1, 2006.
568B
orange/white
orange
green/white
green
www.gantner.com