Frigidaire TFFU2065FW0 Посібник з використання та догляду - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Морозильна камера Frigidaire TFFU2065FW0. Frigidaire TFFU2065FW0 12 сторінок.

Друкувати сторінку

Electrical

information

These

guidelines

must

be fo!lowed

ensure

that

safety

mechanisms

in the design

of this freezer

will operate

properly.

Avoid

fire hazard

electric

shock.

Do not

use an extension

cord

or an adapter

plug.

not remove

any prong

from

power

cord.

Grounding

type

wall

receptacle

Do not under

any

circumstances

cut, remove,

or bypass

the grounding

prong

from

this plug.

Power supply

cord with

3-prong

grounding

plug

•

Refer

to the serial

plate

for

correct

electrical

rating.

The

power

cord

of the

freezer

is equipped

with

a three-prong

grounding

plug for protection

against

shock

hazards.

It must be

plugged

directly

into

its own

properly

grounded

three-prong

receptacle,

protected

with

a 15 amp

time delay

fuse

or circuit

breaker.

The receptacle

must be installed

in accordance

with

the local codes

and ordinances.

Consult

a qualified

electrician.

Receptacles

with

Ground

Fault

Circuit

interrupters

(GFCl)

are

NOT RECOMMENDED.

DO NOT USE AN EXTENSION

CORD OR

AN ADAPTERPLUG.

•

If the voltage

varies by 10 percent

or more, freezer

performance

may be affected.

Operating

the freezer

with

insufficient

power

can damage

the motor.

Such damage

is not covered

under the

warranty.

If you suspect

your voltage

is high or low, consult

your

power

company

for testing.

•

To prevent

the freezer

from being turned off accidentally,

do not

plug the unit into an outlet controlled

by a wall switch

or pull cord.

•

Do not pinch,

knot, or bend

the power

cord

in any manner.

r!_v,v_.1,i_ll#B

Other

Precautions

• To defrost,

always

unplug

unit first.

• Never

unplug

the freezer

by pulling

on the power

cord.

Always

grip the plug firmly

and pull straight

out from

the receptacle.

• Turning

the control

to "OFF"

turns

off the compressor

but does

not disconnect

power

to other

electrical

components.

First

Steps

Before

starting

the freezer,

these

important

first steps.

Installation

/ Freezer

Placement

• Choose

a place

that is near a grounded

electrical

outlet.

• The freezer

should

be located

where

surrounding

temperature

will not exceed

11O°F (43°C).

Temperatures

of 32°F (O°C) and

below

will NOT affect

freezer

operation.

Additional

compressor

heaters

are not recommended.

• Allow

space

around

the unit for good

air circulation.

Leave

a 3

inch

(75mm)

space

on all sides

of the freezer

for

adequate

circulation.

3" AIR SPACE

Installation

Leveling

The freezer

must have

all bottom

corners

resting

firmly

on a solid

floor.

The floor

must

be strong

enough

to support

a fully

loaded

freezer.

It is VERY

IMPORTANT

for your freezer

to be level in order

to function

properly.

If the freezer

is not leveled

during

installation,

the door/lid

may be misaligned

and not close

or seal properly,

causing

cooling,

frost

or moisture

problems.

To level Upright

Units:

After discarding

crating

screws

and wood

base,

use a carpenter's

level

to level

the freezer

from

front

to back.

Adjust

the plastic

leveling

feet in front, ½ bubble

higher,

so that the door closes easily

when

left halfway

open.

To level Chest

Units:

If needed,

add metal

or wood shims

between

feet pads and floor.

CRATING

SCREW

""-

DISCARD

THE

(4)

CRATING

SCREWS

AND

{2) WOOD

BASES

Unpacking

and Leveling

- Upright

Freezers

_[_

To allow door to

close and seal properly, DO NOT let

food packages extend past the front

of shelves,

Shelf Front

.........................................