IKEA IHW8305VS0 Інструкція з монтажу та інструкція з експлуатації та догляду - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу та інструкція з експлуатації та догляду для Вентиляційна витяжка IKEA IHW8305VS0. IKEA IHW8305VS0 28 сторінок. 30"(76.2cm) wall-mount canopy
Друкувати сторінкуINSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill with %e" (8 mm) drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Phillips screwdriver
Parts needed
•
Home power supply cable
•
1/2"(12.7 mm) UL listed or CSA approved strain reliefs
•
3 UL listed wire connectors
For vented installations,
you will also need:
•
1 wall or roof cap
•
Metal vent system
For non-vented
(recirculating)
installations,
you will
also need:
•
Charcoal Filter Kit Part Number 4396848 - for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Hood canopy assembly with ventilator, light bulbs and
transition with back draft dampers installed
•
Deflector for non-vented
(recirculating) installations
•
Filter-
installed in hood canopy
•
3-5x35mmscrews
•
4-4x8mmscrews
•
1-17x8x1.5mmwashers
•
6- 3.5 x 9.5 mm screws
•
4- 2.9 x 6.5 mm screws
•
Torx ®t adapter T10
•
Torx ®adapter T20
•
2-6x70mmscrews
•
2 - 10 x 70 drywall anchors
•
Mounting template
•
Lower support bracket
•
Vent cover bracket
•
2-piece vent cover
IMPORTANT." Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the filter on the rear wall of the range
hood.
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The range hood is factory set for venting through the roof or wall.
For non-vented (recirculating)
installations see "Non-Vented
(recirculating) Installations"
in "Connect Vent System" section.
Charcoal Filter Kit Part Number 4396850 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where range hood will be installed
must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
133/8``
(34.0 cm)
**30%6"
(65.5 cm)
(77.0 cm)
rnin.
rnin.
"42V2....
47_A"
(108.0 crn)
(120.0 crn)
max.
13/8"
(3.5cm)
*Vented installations only
**Non-vented
(recirculating)
installations only
1-®TORX is a registered trademark
of Acument
Intellectual
Properties, LLC.