IKEA LAGAN Посібник - Сторінка 8

Друкувати сторінку

ENGLISH

First Use

Advice regarding the first time use

Before installation and first usage of the appliance please read

carefully „ SAFETY INSTRUCTION" and „ASSEMBLY INSTRUCTION"

available in the product literature bag. Please remember to

remove all transport protection parts from the dishwasher.

Filling the salt reservoir

The use of salt prevents the formation of LIMESCALE on the

dishes andon the machine's functional components.

• It is mandatory that THE SALT RESERVOIR BE NEVER EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and should be filled when the

SALT REFILL indicator light

1. Remove the lower rack and unscrew

2. Position the funnel (see figure) and

3. Only the first time you do this: fill

4. Remove the funnel and wipe any

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash program (this could

damage the water softener beyond repair).

As soon as this procedure is complete, run a program without

loading. The "Pre-Wash" program alone is NOT sufficient.

Residual saline solution or grains of salt can lead to corrosion,

irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such

circumstances.

Only use salt that has been specifically designed for

dishwashers. If the salt container is not filled, the water

softener and the heating element may be damaged

as a result of limescale accumulation. Using of Salt is

recommended with any type of dishwasher detergent.

Whenever you need to add salt, it is mandatory to complete

the procedure before the beginning of the washing cycle to

avoid corrosion.

Setting the water hardness

To allow the water softener to work in a perfect way, it is

essential that the water hardness setting is based on the actual

water hardness in your house. This information can be obtained

from your local water supplier. The factory sets the default value

for the water hardness.

• Switch on the appliance by pressing the ON/OFF button.

• Switch off the appliance by pressing the ON/OFF button.

• Hold down button

for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing quickly the ON/OFF

button.

• The program indicator light of the current set level flashes.

• Press button

to select the desired hardness level (see

WATER HARDNESS TABLE).

• Switch off the appliance by pressing the ON/OFF button.

Setting is complete!

in the control panel is lit.

the reservoir cap (anticlockwise).

fill the salt reservoir right up to its

edge (approximately 1 kg); it is not

unusual for a little water to leak out.

the salt reservoir with water.

salt residue away from the opening.

Water Hardness Table

Level

°dH German

degrees

1 Soft

0 - 6

2 Medium

7 - 11

3 Average

12 - 16

4 Hard

17 - 34

5 Very hard

35 - 50

Water Softening System

Water softener automatically reduces water hardness, conse-

quently preventing scale buildup on heater, contributing also

to better cleaning efficiency. This system regenerates itself with

salt, therefore it is required to refill salt container when empty.

Frequency of regeneration depends on water hardness level

setting - regeneration takes place once per 6 Eco cycles with

water hardness level set to 3.

Regeneration process starts in final rinse and finishes in drying

phase, before cycle ends.

• Single regeneration consumes: ~3.5 L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005 kWh of energy.

Filling the rinse aid dispenser

Rinse aid makes dish DRYING easier. The rinse aid dispenser

should be filled

when when the dark optical indicator on the

dispenser door

becomes transparent

1. Open the dispenser

by pressing and pulling up the tab on

the lid.

2. Carefully introduce the rinse aid as far as the maximum (110

ml) reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Adjusting the dosage of rinse aid

If you are not completely satisfied with the drying results, you

can adjust the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button

three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The program indicator light of the current set level flashes.

• Press button

to select the level of rinse aid quantity to be

supplied.

• Switch it off using the ON/OFF button.

Setting is complete!

°fH French

°Clark English

degrees

0 - 10

0 - 7

11 - 20

8 - 14

21 - 29

15 - 20

30 - 60

21 - 42

61 - 90

43 - 62