Green Power GPCC3012 Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Вивіз сміття Green Power GPCC3012. Green Power GPCC3012 3 сторінки.

Друкувати сторінку

Owner's Manual

Operation Instructions

1. LED indicator and seven-segment digital display

Connect the charger to the battery. Turn on the mains. The charger enters the charging mode (the battery type indicator shows the default battery

type). The status indicator - % Percent, Battery Voltage, Charging Current and the seven-segment digital display will show the charging status.

Seven-segment digital display

＠

Battery capacity % indicator

Battery voltage indicator

Powering

everyday

everywhere!

5 s:

Change charging profile

Press

10 s:

Start EQ mode (Wet Battery)

Select button Charging current indicator

2. Common Mode(Default) & BMS Mode

a. The charger enters BMS mode when being connected to lithium-ion battery through Can Bus;

b. For safety reason, the charger will flash "bnS" if being reconnected to Lead-acid battery under a BMS mode;

c. Press & hold the Select button for 3 seconds in BMS mode to release the curve number, that is, switch back to normal mode.Press & hold

the Select button for 1 seconds to choose the desired profile.

Status indicator and seven-segment digital display:

% Percent: Battery capacity % indicator. i.e. 10, 20, 30...... 100 (%)

Battery Voltage (V): Battery voltage indicator. i.e. 24.0(V)

Charging Current (A): Charging current indicator. i.e.15 (A)

To change the charging profile, press & hold the Select button

for 5 seconds, then press the Select button to choose the

desired profile. Once selected, press & hold the Select key for

5 seconds, and the charging profile selection will be completed.

To start EQ mode, press & hold the Select button for 10

seconds, and display will show EQ mode. The next charging

cycle will go into EQ mode. If you want to quit the EQ mode,

hold the Select button for 10 seconds. When display shows

OFF, the charger will quit the EQ mode.

Note: Each operation interval is 5 seconds. If the operation

interval exceeds 5 seconds, it will automatically return to the

default setting.

4. The instruction for cable connection:

1 Connect the battery.

2 Interlock Cable (When charger is charging, the interlock

cables will form an open circuit with no voltage. When charger is not charging, the

interlock cable will form a short circuit with no voltage).

3 Connect AC input wires.

4 Connect CANBUS or LED light wire (Optional function)

Warning: Assure the battery connection cable is

well connected with the charger before it is connected to the battery. Otherwise, the

battery short circuit may occur and cause personal injury or damage to the battery.

Fault Indicator

fault code

Fault Cause

E01

The battery is not well connected

or battery reversely connected or

battery damaged.

E02

Abnormal AC Power Input (Voltage).

Charger High Temperature

E03

Protection.

E04

Battery High

Temperature Protection.

1) Discharging activities during charging cycle.

E05

2) Battery low voltage detected during charging

cycle.

3) Output current is too high

(E05 will reappear even after unit reset).

Battery Voltage is too high.

E06

Address declaration failure

E07

Internal error in product.

E08

Relay Fault

E10

Battery error (battery damaged or

E11

battery system error)

Maintenance Instructions

1. Do not expose charger to oil, dirt, mud or direct heavy water spray when cleaning vehicle.

2. The enclosure of the charges has been tested successfully to IEC 60529, meeting IP66

3. If the detachable input power supply cord set is damaged, replace with a cord that is a safety approved detachable cord, 3 conductor, 1.5

mm² minimum, and rated appropriate for use in the country of destination and, on the other end, an output grounding type IEC 60320 C14 plug.

Product Specifications

Model

Voltage-Range(V)

Current-Range(V)

Output Power(W)

Power Error(%)

DC Output

Applicable to Battery

Reverse Polarity

Short Circuit

Voltage-Range(V)

Frequency(Hz)

AC Input

Current-max(A)

Full Load AC Power Factor

Dimensions

Weight

Operating Temperature

Storage Temperature

。

DC OUTPUT

CANBUS/LED AC INPUT

Solution

1) Check battery connection is correct.

2) Check charger connection is correct.

3) Check each battery is good..

1) Check AC input cord is connected between charger and AC outlet.

2) Make sure AC plug is tightly inserted into AC outlet.

1) Charger shuts down and enters protection mode due to charger/environmental

temperature is too high. Please place the charger in a well-ventilated environment.

2) Disconnect the charger and wait for 15-20mins before reconnecting for charging.

1) Charger will reduce current even stop charging to prevent the battery from

overheating when battery temperature exceeds the preset value.

2) When the battery temperature drops, the charger will restart automatically.

1) Make sure no discharging activity during chargingoperation.

2) Reset charger (disconnect AC power and reconnect for a 2nd charge cycle).

3) If E05 reappear within 10 minutes, please return charger to factory for repairing.

Check and assure that the correct output battery voltage is connected.

Return to the factory for repairing.

Replace battery

or IP67 (see silk screen of the device).

GPCC1524

GPCC1724

0-34V

0-15A

0-17A

510W

578W

AGM, WET, GEL, Lithium

Electronic protection-auto-reset

100-240V

50-60Hz

>0.98

22.6*15.2*8.1cm

2.5KG

-40℃~+65℃

-40℃~+70℃

INTERLOCK

。

GPCC3012

0-17V

0-30A

510W