ALIBI ALI-CD1720EC Посібник зі швидкого встановлення
Переглянути онлайн або завантажити pdf Посібник зі швидкого встановлення для Камера спостереження ALIBI ALI-CD1720EC. ALIBI ALI-CD1720EC 2 сторінки. Hd-tvi/cvbs turret camera
Друкувати сторінкуALI-CD1720EC HD-TVI/CVBS Turret
Camera Quick Installation Guide
The ALIBI ALI-CD1720EC turret camera include a high sensitivity sensor and advanced circuit design
technology. They feature high resolution, low image distortion and low noise features which makes them
suitable for surveillance and image processing systems.
Features
Hardware configurable HD-TVI or CVBS output
•
HD-TVI technology transmits zero latency HD video resolution over coax cabling
•
1280 x 720 (720p @ 30 fps) HD video using HD-TVI for sharp, detailed images,
•
or 1000 TVL CVBS video
3.6 mm lens captures images over a large area
•
Built-in 24 LEDs enables the camera to see up to 65 ft in the dark
•
Smart IR technology reduces over-exposure of the IR LEDs at the center of the image
•
True day/night (ICR) captures sharp, clear images in low light and at night
•
-40°F ~ 140°F extreme temperature operating range
•
IP66 weather-rated ABS housing
•
Cable
channel
Locking
bezel
Housing
IR array
Lens
Camera
module
ALI-CD1720EC camera assembly
Camera drop cable connectors
What's in the box
Camera assembly
•
Mounting screws and wall inserts
•
This manual
•
Drill template
•
Installation
Before installation:
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
•
provide the rated voltage and wattage for the camera. See the Specifications section.
www.observint.com
1
Mounting
plate
Light
sensor
HD-TVI or CVBS Video
BNC Connector
Power Connector
CVBS Switch: Short wires
together for CVBS output
What you need
12 Vdc power source. See Specifications for
•
voltage and wattage requirements.
Tools and additional fasteners (may be required)
•
for mounting the camera
Video and power extension cable
•
HD-TVI or CVBS video setup monitor (optional)
•
During installation:
Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
•
array shield becomes soiled, clean it only with approved products. See the
Camera drop cable: The camera drop cable includes two connectors:
•
Video BNC connector: For transmission of the video signal across a coax (75 Ω) extension
—
cable to an HD-TVI or CVBS compatible recorder.
Power connector: When applying power, observe the power polarity. See the picture to the
—
right for the connector polarity configuration.
These cameras can be mounted on a wall or ceiling that has sufficient strength to support it. The video/
power drop cable from the camera can be routed either through mounting surface or through a cable
channel on the edge of the mounting plate.
1.
Unscrew the bezel from the mounting plate, and then lift it off of the camera.
2.
Separate the housing and the camera module from the mounting plate.
Mounting
Camera module
plate
3.
Using the mounting template or the mounting plate, mark the holes for the camera mounting
screws.
4.
Drill holes for the screws that anchor the plate to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface material and strength,
more appropriate fasteners may be required.
5.
Drill a 3/4" hole through the mounting surface for the drop cable, if necessary.
6.
If using wall inserts for the mounting screws, install the wall inserts at this time.
7.
Attach the mounting plate the surface using the appropriate fasteners. If the camera drop cable will
route through a cable channel, lay the cable in the channel before tightening the mounting screws.
Mounting
plate
section.
Cleaning
Housing
Bezel
ALI-CD1720EC_CQ
160201