Avantco Equipment 177SL612A Посібник користувача - Сторінка 7
Переглянути онлайн або завантажити pdf Посібник користувача для Кухонна техніка Avantco Equipment 177SL612A. Avantco Equipment 177SL612A 16 сторінок. Meat slicer
Також для Avantco Equipment 177SL612A: Посібник користувача (16 сторінок)
Друкувати сторінку
Only use hot water and a biodegradable detergent for dishes with a 7-8 PH,
Only use hot water and a biodegradable detergent for dishes with a 7-8 PH,
at a temperature of no lower than 30° C or(86° F) using a soft, spongy cloth and a
at a temperature of no lower than 30° C or(86° F) using a soft, spongy cloth and a
semi-rigid nylon brush for the plate and the sharp food press.
semi-rigid nylon brush for the plate and the sharp food press.
The sanitizer concentration shall comply with Section 4-501.114, Manual and
The sanitizer concentration shall comply with Section 4-501.114, Manual and
Mechanical Warewashing Equipment, Chemical Sanitization – Temperature, pH,
Mechanical Warewashing Equipment, Chemical Sanitization – Temperature, pH,
Concentration, and Hardness of the FDA Food Code.
Concentration, and Hardness of the FDA Food Code.
recommend using USDA approved sanitizer
recommend using USDA approved sanitizer
If a chemical sanitizer other than chlorine, iodine or quaternary ammonium is used, it
If a chemical sanitizer other than chlorine, iodine or quaternary ammonium is used, it
shall be applied in accordance with the EPA-registered label use instructions.
shall be applied in accordance with the EPA-registered label use instructions.
: For cleaning the sharp areas of the plates, the food press and the
: For cleaning the sharp areas of the plates, the food press and the
blade, we recommend using protective gloves.
blade, we recommend using protective gloves.
Rinse well with a lot of hot clean water and dry with a soft cloth or a spongy
Rinse well with a lot of hot clean water and dry with a soft cloth or a spongy
material. Do not clean the slicer with water or stream jets or similar methods.
material. Do not clean the slicer with water or stream jets or similar methods.
Clean all the removed parts using a cloth and a cleaning solution. Rinse with hot
Clean all the removed parts using a cloth and a cleaning solution. Rinse with hot
water. Sanitize and let air dry.
water. Sanitize and let air dry.
Clean the sharpener cover with water and detergent. Carefully clean the
Clean the sharpener cover with water and detergent. Carefully clean the
sharpener assembly and around the stones.
sharpener assembly and around the stones.
assembly
assembly
Each
Each
time
time
the
the
sharpener
examined for cleanliness. Turn off the slicer, close the gauge plate, unplug power
examined for cleanliness. Turn off the slicer, close the gauge plate, unplug power
cord and open the sharpener cover.
cord and open the sharpener cover.
If there is evidence of fatty or metallic build-up in the stones, they must be
If there is evidence of fatty or metallic build-up in the stones, they must be
cleaned. Otherwise, they will not have the abrasive quality necessary to sharpen.
cleaned. Otherwise, they will not have the abrasive quality necessary to sharpen.
Clean as follows:
Clean as follows:
Remove the nuts and take the stones off the shafts.
Remove the nuts and take the stones off the shafts.
Soak the stones in a solution of dish soap (i.e. Joy, Dawn, etc.) and water for
Soak the stones in a solution of dish soap (i.e. Joy, Dawn, etc.) and water for
one hour.
one hour.
www.Avantco.com
www.Avantco.com
www.AvantcoEquipment.com
sharpener
is
is
used,
used,
the
User Manual
User Manual
User Manual
submerge the sharpener
submerge the sharpener
the
sharpening
sharpening
stones
stones
should
should
be
be
7