Makita AN451 Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Електроінструмент Makita AN451. Makita AN451 20 сторінок. Pneumatic roofing coil nailer
Також для Makita AN451: Перелік деталей (5 сторінок), Розбивка на частини (4 сторінок), Інструкція з експлуатації (19 сторінок)

Друкувати сторінку

(7) Do not load the tool with fasteners

when any one of the operating con-

trols is activated.

(8) Do not operate the tool with any power

source other than that specified in the

tool operating/safety instructions.

6. An improperly functioning tool must not

be used.

7. Sparks sometimes fly when the tool is

used. Do not use the tool near volatile,

flammable materials such as gasoline,

thinner, paint, gas, adhesives, etc.; they

will ignite and explode, causing serious

injury.

8. The area should be sufficiently illumi-

nated to assure safe operations. The area

should be clear and litter-free. Be espe-

cially careful to maintain good footing and

balance.

9. Only those involved in the work should be

in the vicinity. Children especially must be

kept away at all times.

10. There may be local regulations concern-

ing noise which must be complied with by

keeping noise levels within prescribed

limits. In certain cases, shutters should be

used to contain noise.

11. Do not play with the contact element: it

prevents accidental discharge, so it must

be kept on and not removed. Securing the

trigger in the ON position is also very dan-

gerous. Never attempt to fasten the trig-

ger. Do not operate a tool if any portion of

the tool operating controls is inoperable,

disconnected, altered, or not working

properly.

12. Operate the tool within the specified air

pressure on the tool label for safety and

longer tool life. Do not exceed the recom-

mended max. operating pressure. The

tool should not be connected to a source

whose pressure potentially exceeds 14.0

kgf/cm

G (200 PSIG).

13. Never use the tool with other than com-

pressed air. If bottled gas (carbon dioxide,

oxygen, nitrogen, hydrogen, air, etc.) or

combustible gas (hydrogen, propane,

acetylene, etc.) is used as a power source

for this tool, the tool will explode and

cause serious injury.

14. Always check the tool for its overall condi-

tion and loose screws before operation.

Tighten as required.

15. Make sure all safety systems are in work-

ing order before operation. The tool must

not operate if only the trigger is pulled or

if only the contact element is pressed

against the wood. It must work only when

both actions are performed. Test for pos-

sible faulty operation with nails unloaded

and the contact element in fully pulled

position.

16. Check walls, ceilings, floors, roofing and

the like carefully to avoid possible electri-

cal shock, gas leakage, explosions, etc.

caused by striking live wires, conduits or

gas pipes.

17. Use only nails specified in this manual.

The use of any other nails may cause mal-

function of the tool.

18. Do not permit those uninstructed to use

the tool.

19. Make sure no one is nearby before nailing.

Never attempt to nail from both the inside

and outside at the same time. Nails may

rip through and/or fly off, presenting a

grave danger.

20. Watch your footing and maintain your bal-

ance with the tool. Make sure there is no

one below when working in high loca-

tions, and secure the air hose to prevent

danger if there is sudden jerking or catch-

ing.

21. On rooftops and other high locations, nail

as you move forward. It is easy to lose

your footing if you nail while inching back-

ward. When nailing against perpendicular