ALIBI ALI-NS2126R Посібник зі швидкого встановлення - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник зі швидкого встановлення для Цифрова камера ALIBI ALI-NS2126R. ALIBI ALI-NS2126R 7 сторінок. 6mp vari-focal ip turret camera
Друкувати сторінку
For cameras connected directly to an NVR
Refer to the firmware manual for your NVR for specific instructions to perform the following:
1.
Log into the NVR at the NVR console.
In the Live View display, find the PTZ camera you installed. Click on the camera to open the
2.
Quick Setting toolbar.
PTZ Control icon
Click the PTZ Control icon. See above.
3.
4.
In the pop-up PTZ menu, click the PTZ Control tab. See below.
5.
In the PTZ Control panel, click the zoom and focus buttons labeled in the graphic above. Verify
that the camera performs as expected. Refer to the Specifications section of this document for
motion and zoom ranges.
Step 9.
Adjust the camera image for your surveillance target
Use the firmware menus to adjust the brightness, contrast, saturation and sharpness of the video image
if necessary. These settings are initially optimized at the factory and may not need adjustment. When
adjustments are necessary, the paths to the image settings menus are different if the camera is installed
as a device on a LAN, or if it is connected to a NVR. Select the installation type below for your camera to
complete this step.
For cameras installed on a LAN
1.
If necessary, log into the camera on the LAN with administrative credentials.
After adjusting the camera for the a typical field of view, click the Setup tab, and then click the
2.
Image link in the left frame.
3.
Adjust the Brightness Contrast, Saturation and Sharpness of the image. Each parameter can be
set to a level of 0 ~ 100 either by moving the slider or entering the value in the box on the right.
The effect of the adjustment will appear in the Live View image in the menu.
6
www.observint.com
Refer to the firmware user manual for your camera to use the other submenus on this screen.
For cameras connected directly to an NVR
1.
Log into the NVR with administrative privileges.
Open the firmware Image menu. Go to Menu | Camera Management | Image
2.
In the Camera field drop down list, select the camera you want to configure. In the example
3.
above, [D1]IPCamera 01 is selected.
Drag the Brightness, Contrast, Saturation and Hue adjustment markers left or right to
4.
perfect the image from the camera. For some adjustments, you can click the up ( 5 )or down
( 6 )icons near the adjustment value (on the right side) to incrementally change the value of
those adjustment.
Click Apply to save your settings for this camera.
5.
Refer to the firmware user manual for your NVR to use the other submenus on this screen.
Specifications
Zoom In / Out
Focus In / Out
Camera
Iris Open / Close
Image Sensor
Signal System
Min. Illumination
Shutter speed
Slow shutter
Auto Iris
Lens Mount
Adjustment Range
Day& Night
Wide Dynamic Range
Digital noise reduction
Focus
Lens
Lens, FOV
Lens Type
Aperture
Focus
Lens Mount
IR
IR Range
Wavelength
Compression Standard
Video compression
H.264 Type
H.264+
H.265 Type
H.265+
ALI-NS2126R
1/2.9" Progressive Scan CMOS
PAL / NTSC
Color: 0.01 Lux @ (F1.2, AGC ON), 0.018 Lux @ (F1.6, AGC ON), 0 Lux with IR
1/3 second to 1/100,000 second
Supported
Not supported
φ14
Pan: 0° ~ 355°, tilt: 0° ~ 75°, rotate: 0° ~ 360°
IR cut filter
120 dB
3D DNR
Motorized VF lens
2.8 ~ 12 mm
Horizontal field of view: 88° to 27°
Vertical field of view: 56° to 18°
Diagonal field of view: 110° to 33°
Motorized
F1.6
Auto
φ14
100 ft (up to 30 m)
850 nm
Main stream: H.265 / H.264
Sub stream: H.265 / H.264 / MJPEG
Third stream: H.265 / H.264
Main Profile / High Profile
Main stream supported
Main Profile
Main stream supported
© 2019 Observint Technologies. All rights reserved.