Lexmark 240n - E B/W Laser Printer Короткий довідник

Переглянути онлайн або завантажити pdf Короткий довідник для Принтер Lexmark 240n - E B/W Laser Printer. Lexmark 240n - E B/W Laser Printer 2 сторінки. Lexmark e240: quick reference
Також для Lexmark 240n - E B/W Laser Printer: Налаштування та встановлення (2 сторінок)

Друкувати сторінку

Quick Reference

Loading the 250-sheet or 550-sheet tray

Remove the tray.

Note:

Loading paper or other print media

Source

Sizes

Types

Capacity

(sheets)

Prepare a stack of paper for loading by flexing or fanning it back

and forth. Straighten the edges on a level surface.

Tray 1

A4, A5, JIS B5,

Plain paper,

250 paper;

Load the paper in the tray with the print side facing down.

(250-sheet tray)

letter, legal,

paper labels,

50 labels;

executive, folio,

transparencies

50 transparencies

statement,

Tray 2*

Plain paper,

550 paper;

Universal

(550-sheet tray)

paper labels,

50 labels;

transparencies

50 transparencies

Manual feeder

A4, A5, JIS B5,

Plain paper,

letter, legal,

paper labels,

executive, folio,

transparencies,

statement,

card stock

Universal

7¾, 9, 10, DL,

Envelopes

C5, B5, other

* Tray 2 not available on all models.

Capacity for 20 lb print media, unless otherwise noted.

Universal size ranges:

– Tray 1: 89–216 x 210–356 mm (3.5–8.5 x 8.27–14.0 in.)

– Tray 2: 148–216 x 210–356 mm (5.83–8.5 x 8.27–14.0 in.)

– Manual feeder: 76–216 x 127–356 mm (3.0–8.5 x 5.0–14.0 in.) (includes

3 x 5 in. cards)

Note:

To help prevent jams:

•

Flex all stacks of print media back and forth to loosen them, and

then fan them before loading. Do not fold or crease the print

Make sure the paper is below the maximum fill lines on the side

media. Straighten the edges of the stack on a level surface.

guides. Overloading may cause jams.

Slide the two side guides and the back guide until they fit snugly

against the stack of paper.

•

Do not exceed the maximum stack height.

•

Never mix media types within a tray.

Insert the tray.

If you are going to load legal or folio size paper, you

have to extend the length of the paper tray. See

"Extending the tray for legal or folio size paper" for

instructions.

Extending the tray for legal or folio size paper

Press down on the pressure point at the back of the tray.

Expand the tray until the extender locks into place.

Load letterhead paper with the design side facing

down. The top edge of the sheet with the logo should

be placed at the front of the tray.

Using the manual feeder

•

Hold transparencies by the edges, and avoid touching the print

side. Oils from your fingers that are deposited on the

The manual feeder can only feed one sheet of print media at a time.

transparency can affect print quality.

Send your print job to the printer (see to the User's Reference on

•

Load letterhead face-up, with the top of the sheet first.

the publications CD for help).

Using the rear exit

The printer Load Paper

light blinks when it is ready for the

print media to be loaded.

The single-sheet rear exit provides a straight-through paper path to

Place a sheet of the selected print media, print side facing up, at

help reduce curling and potential jams. This is especially useful for

the center of the manual feeder, but only to the point where its

specialty media, such as transparencies, envelopes, labels, card

leading edge can contact the paper guides.

stock, or index cards.

Adjust the paper guides to the print media width.

Hold both sides of the print media close to the manual feeder and

push it into the printer until it automatically engages.

There is a brief pause between the time the printer engages the

print media and when it feeds into the printer.

When the rear exit door is open, all print media comes out the rear exit.

When closed, all media is sent to the output bin on top of the printer.

Warning:

Do not force the print media into the feeder. Forcing the

media causes jams.

•

Insert envelopes with the flap side face down and with the stamp

area as shown.

Printing on specialty media

Follow these instructions to print on media such as transparencies,

card stock, labels, or envelopes. The type of print media you want to

use determines which tray or feeder it should be fed from.

Load the print media as specified for the tray you are using. See

Loading paper or other print media

for help.

From the computer software application, set the paper type, size,

and source according to the media you loaded.

From the computer software application, select File

Print.

Click Properties (or Options, Printer, or Setup, depending on

the application) to view the printer driver settings.

Click the Paper tab.

Select your media type (transparencies, envelopes, and so

on) from the Form Type list box.

Select the tray or feeder containing the specialty media from

the Form Source list box.

Select the size of the specialty media from the Form Size list

box.

Click OK, and then send your print job as usual.

Canceling a print job

Press and release Cancel

on the printer operator panel to cancel

the job currently printing. The Cancel job light sequence is displayed

on the operator panel while the job is being canceled.

P/N 28S1821

*28S1821*

Printed in China

E.C. 28S014

6/05