Jandy CPHVLEDS50 Посібник з монтажу - Сторінка 8
Переглянути онлайн або завантажити pdf Посібник з монтажу для Освітлювальне обладнання Jandy CPHVLEDS50. Jandy CPHVLEDS50 16 сторінок. Watercolors led lights underwater large and small light
Також для Jandy CPHVLEDS50: Посібник з монтажу (20 сторінок)
Друкувати сторінку
Page 8
English
section 5. Wiring Options for
Controlling Jandy Pro
series WaterColors lED
lights
nOTE
The Jandy Pro series WaterColors lights will not
operate properly with light dimmers. Do not wire the
Jandy Pro Series Lights to any dimming circuitry.
To the extent allowed by code and capacity of the
electrical equipment, multiple Jandy Pro Series lights
may be controlled with a single switch so their colors will
always be synchronized.
Separate switches may be used to control the on/off
and color functions of each Jandy Pro Series light. It is
recommended that these switches be located next to each
other to facilitate simple color synchronization when
desired. All switches must be operated at the same time
to assure color synchronization. Otherwise, the lights will
work independently of each other.
5.1
Wiring to an Aqualink
system
The Jandy Pro Series WaterColors Lights can be wired
into the Jandy Pro Series AquaLink RS control system
to provide simplified operation of the lights, as well as a
means to synchronize the color change function. Connect
the lights to one of the auxiliary relays in the Power
Center.
nOTE
It is recommended to connect one light per relay so
each light can be controlled separately. However, up to
four lights can be connected on a single relay. If there
are more than four lights installed on one AquaLink RS
system, ensure there is more than one auxiliary relay
available in the Power Center.
Refer to Figures 2 and 3 to connect the Jandy Pro Series
Color Lights to the Power Center.
CAUTiOn
A Ground Fault Circuit Interrupter (GFCI) must be
provided for 120 volt models. The conductors on the
load side of the GFCI circuit shall not occupy conduit,
boxes, or enclosures containing other conductors
unless the additional conductors are also protected by
a GFCI. Refer to local codes for complete details.
nOTE
The Jandy Pro Series WaterColors Lights are available
in 120-volt and 12-volt versions. If installing a 12-volt
light, a 120-volt/12-volt step-down (AC) transformer
must be used. For more information about 12-volt
installations, refer to Section 8 of this manual.
Jandy
Pro Series, WaterColors LED Lights
®
5.2
The Jandy Pro Series WaterColors Lights can be wired
into a basic time clock to automatically turn on the lights
at a predesignated time. Refer to Figure 4 to connect the
lights into the time clock.
5.3
The Jandy Pro Series WaterColors Lights can be wired
into a switch to manually turn on/off the lights. Refer to
Figure 5 to connect the lights into the switch.
section 6. Jandy Pro series
6.1
Turn the light ON. The first time the light is turned on,
the color sequence begins with the Alpine White. To
Rs Control
®
change the color, turn the light OFF and then ON within
three (3) seconds. Continue turning OFF and ON until
the desired light color mode is reached. See Table 1 for
the color mode sequence.
Table 1.
nOTE
|
Installation Manual
Wiring to a Time Clock
Wiring to a switch
WaterColors lED light
Operating instructions
To Operate the light and Change
Colors
Jandy Pro series WaterColors lights
sequence
sequence Order
1
Alpine White
2
Sky Blue
3
Cobalt Blue
4
Caribbean Blue
5
Spring Green
6
Emerald Green
7
Emerald Rose
8
Magenta
9
Violet
10
Slow Color Splash
11
Fast Color Splash
12
America the Beautiful
13
Fat Tuesday
14
Disco Tech
When the light is turned OFF for more than seven (7)
seconds, it will remain in the color set that is currently
active. When the light is turned back ON, the light will
be on the same color set.
Color Modes