Jandy Stealth SHPM Посібник з монтажу та експлуатації - Сторінка 12

Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Водяний насос Jandy Stealth SHPM. Jandy Stealth SHPM 20 сторінок. Pro series stealth pumps

Друкувати сторінку

Page 12

ENGLISH

Section 4. Operation

4.1

Start-up

CAUTION

Never run the pump without water. Running the

pump "dry" for any length of time can cause severe

damage to both the pump and motor and will void

the warranty.

If this is a new pool installation, make sure all piping

is clear of construction debris and has been properly

pressure tested. The filter should be checked for

proper installation, verifying all connections and

clamps are secure according to the manufacturer's

recommendations.

WARNING

To avoid risk of property damage, severe personal

injury, or death, verify that all power is turned off

before starting this procedure.

Release all pressure from the system and open

the filter pressure release valve.

If the pump is located below the water level

of the pool, opening the filter pressure release

valve will prime the pump with water.

If the pump is located above the water level of

the pool, remove the lid and fill the basket with

water before starting the pump.

Prior to replacing the lid, check for debris

around the lid o-ring seat. Debris around the lid

o-ring seat will cause air to leak into the system,

and make it difficult to prime the pump.

Hand-tighten the lid to make an air tight seal.

Do not use any tools to tighten the lid, hand-

tighten only. Make sure all valves are open and

the unions are tight.

Turn on the power to the pump. Then turn on

the pump.

Once all the air has left the filter, close the

pressure release valve.

The pump should prime. The time it takes to

prime will depend on the elevation and length

of pipe used on the suction supply pipe. See

Section 3.1.3.3 for proper elevation and pipe

size.

If the pump does not prime and all the

instructions to this point have been followed,

check for a suction leak and then repeat Steps 2

through 7.

Jandy

Pro Series Stealth

Pumps

™

Section 5. Service and

5.1

Inspect the pump basket for debris by looking through

the clear pump lid. Remove any debris, because as

debris accumulates, it will begin to block the flow

of water through the pump. Keep the basket clean to

improve the performance of the pump.

A misaligned basket will cause the lid to be

improperly seated, allowing an air leak, which could

result in pump damage.

10.

Operation Manual

Maintenance

Routine Maintenance

Turn off the power to the pump. If the pump

is located below the water level, close the

isolation valves on the suction and discharge

sides of the pump to prevent a backflow of

water.

Turn the lid's locking ring counter-clockwise

until 'START' aligns with the ports. (You may

use a tool for leverage to open the lid, but never

to tighten the lid when closing it.) Carefully

remove the lid.

CAUTION

Lift the basket out of the pump.

Dispose of the debris and thoroughly clean

the basket, making sure all the holes are open.

Using a garden hose, spray the basket from the

outside to help clear the holes. Use your hands

to remove any remaining debris.

Replace the basket in the pump by aligning

the opening with the suction pipe. If aligned

properly, the basket will drop easily into place.

Do not force into place.

Prior to replacing the lid, check for debris

around the lid o-ring seat, as this will cause air

to leak into the system. Clean the lid o-ring and

place it on the lid.

Hand-tighten the lid to make an air tight seal.

Do not use any tools to tighten the lid: hand-

tighten only.

Verify that all valves have been returned to the

proper position for normal operation.

Open the pressure release valve on the filter,

and make sure it is clean and ready for

operation.

Turn on the power to the pump. Once all the

air has been evacuated from the filter, close the

pressure release valve.